Availability of 6 Pin to 7 Pin Adapter

Question

Question:

I AM LOOKING FOR A CABLE WITH A 6 PIN MALE ROUND TERMINAL CONNECTOR TO A 7 PIN FLAT TERMINAL CONNECTOR. To be used to hook a slide on truck camper to 2014 Dodge Ram 2500 truck

asked by: Roy C

0

Expert Reply:

There a couple adapters which might work for you, the Hopkins # 47435 6-Pole to 7-Pole or the RoadMaster # RM-146-7. I've left links to video reviews of both adapters for you to take a look at.

expert reply by: Kyle S

0

Answer 1

The blue wire of a 7-way runs to the blue wire of a brake controller to activate the trailer's brakes. If you don't have a brake controller or a need for trailer brakes you'd simply not use that circuit. I attached a diagram that has the…

view full answer...

Answer 2

The Hopkins 6 Pole to 7 Pole Adapter, #47435, does have a pin for the brake output for a brake controller. This adapter will work for your set up as long as the center pin of the 6-way plug on your RV is for 12v power and the pin in the 10 o clock…

view full answer...

Answer 3

It sounds like you need to add a 7-Way RV style trailer connector to your 1997 Chevy pickup. Since you already have a connector, you will just need to add a 4 and 7 Way Installation Kit, #ETBC7. Though I am not certain if you have a 5-Way flat…

view full answer...

Answer 4

It sounds like there might be some other fuses that could have blown, or there are some shorts on your brake controller/7-way circuits. It is hard to know exactly where the problem lies, but the first thing I would check would be to test the manual…

view full answer...

Answer 5

Sounds like you have a Tekonsha Primus IQ brake controller part #TK90160. I attached a link to this page that has the owners manual/install instructions and then for a replacement wiring harness you'd want the part #20127.

view full answer...

Answer 6

To see a couple diagrams that show how the 6-way to 7-way adapter part #47435 is wired up check out the pictures I attached. The 6-way of this adapter has the center pin as the 12 volt circuit. That is the usual circuit that gets moved around on…

view full answer...

Answer 7

You could indeed use an adapter like the Hopkins 6-way to 7-way adapter, part #47435. Keep in mind, there are two accepted ways of wiring a 6-way trailer connector. One uses the center pin as the 12-v feed, the other uses the center pin as the output…

view full answer...

Answer 8

I looked at the owner's manual for your 2014 Chevrolet Silverado 1500, and for the 4WD Crew Cab, Standard Box with a 5.3L Engine and a 3.42 axle ratio, the maximum trailer weight for the vehicle to tow is 9,500 pounds. The GCWR (Gross Combined…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Availability of 6 Pin to 7 Pin Adapter

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching