Can Camco Countertop Extension CAM43421 Install on a Rounded Edge

Question

Question:

Can this extension be installed if the countertop edge is rounded?

asked by: Jim

0

Expert Reply:

When there isn't a sufficient flat surface to mount Camco Oak Accents RV Countertop Extension # CAM43421 you can mount it lower on the wall of the cabinet beneath the countertop as shown in the picture I have included.

expert reply by: Michael H

0

click to enlarge

Answer 1

Hey Katja, the Curt Echo Mobile brake controller part #C51180 would be your best option. This is a wireless brake controller and all it requires is a 7-way with the taillight functions and the 12 volt accessory circuit active and you'd be set. So…

view full answer...

Answer 2

For your 3,300 lbs trailer, I recommend the Fastway e2 Weight Distribution w/ 2-Point Sway Control item #FA92-00-0450. This system is specifically designed for lighter weight trailers like yours. You don't want to use a higher capacity system…

view full answer...

Answer 3

For your Rockwood A-Frame Pop-up camper I recommend the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37040ET. This weight distribution system has a tongue weight capacity of 400 lbs and a gross towing weight of 4,000 lbs.…

view full answer...

Answer 4

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Can Camco Countertop Extension CAM43421 Install on a Rounded Edge

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching