Replacement Ball Set for Rapid Hitch Andersen Adjustable Ball Mount part # AM3410

Question

Question:

How do you replace a damage, or different size ball??

asked by: Mike H

0

Expert Reply:

For the Rapid Hitch Andersen Adjustable Ball Mount part # AM3410 we have replacement ball sets like part # AM3424 that has the same size balls or part # AM3425 for a 1-7/8 inch and 2 inch hitch ball size.

expert reply by: Jameson C

0

Answer 1

The difference is the finish of the two couplers. The Demco coupler part #DM13203-95 is a galvanized metal finish which is basically a zinc coating and the #DM13203-52 on the other hand is a silver powdercoat finish which is basically like a really…

view full answer...

Answer 2

Hey Kelvin, From what I can find the Titan Model 6 brake actuators have their bolt holes almost in a straight line at the bottom of the coupler so you would have drill new holes in order to mount a new brake actuator. It also shows the Model 6 having…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement Ball Set for Rapid Hitch Andersen Adjustable Ball Mount part # AM3410

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching