Diameter of Curt Round, Snap-Ring Swivel Jack Crank Tube

Question

Question:

This for a top crank model jack2000#. Can you tell me what size the shaft is where the crank handle attaches to is?

asked by: James

0

Expert Reply:

The diameter of the topwind handle on the Curt Jack part # C28304 is 1/2 inch. This is the round metal section that attaches to the crank of the jack and the red knob.

expert reply by: Jameson C

0

Answer 1

The overall retracted height of the Bulldog jack part #BD171401 that you mentioned from bottom of the jack to the top of the handle is 15-1/4 inches.

view full answer...

Answer 2

Unfortunately, the only information I could obtain from NAPA regarding your 8215214 tongue jack is it is rated for a 5,000lb lift capacity, is 14-1/5" tall and has a top wind handle. The Bulldog #BD171401 is going to be the closest option but…

view full answer...

Answer 3

I spoke with my contact at Dutton-Lainson and he gave me the dimensions of this Replacement Snap Ring #DL22672. Inner Diameter = 2.27 Thickness = .080 Outer Diameter = 2.625

view full answer...

Answer 4

The Pro Series trailer jack part #PS1401140303 that you referenced is designed to fit on a pipe mount diameter of 2 inches so if that's the size you have now (it looks like you do) then yes, this would easily fit on the same mount for an easy…

view full answer...

Answer 5

We have a number of jacks that fall within the 3,000 lb to 5,000 lb capacities, however, the only jack that we carry that is similar to the Pro Series, Snap-Ring Swivel Jack, #PS1401020303, is the Bulldog Round, Snap-Ring Swivel Jack, #BD171401. This…

view full answer...

Answer 6

A snap ring like #FP908600 can be measured using a set of dial calipers or digital calipers to get the most accurate measurement possible. To measure the inside diameter, on the inside of the rind measure across at the widest point (not at the bottom…

view full answer...

Answer 7

They make snap ring pliers that are used to remove snap rings. It has two pins on the end that stick into the holes of the snap ring and when squeezed it will open up the ring enough to be removed. You might also try to use 2 regular pliers. With one…

view full answer...

Answer 8

You are correct, the Fulton Snap Ring, #FP908600, and Bulldog Snap Ring, #BD500241, are very similar. I went out to the warehouse and pulled both parts to measure them using digital calipers. Both had the following measurements: Inner diameter = 2.28…

view full answer...

Answer 9

In order to find which snap ring you need you would have to measure the outer diameter of the snap ring bracket on your trailer frame. A part like the #DL22672 REPL Snap Ring for Swivel Trailer Jacks - 2-5/16" Inner Diameter will fit trailer…

view full answer...

Answer 10

The Fulton Round, Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10" Lift - 1,200 lbs #FTJ12000101 has a pilot hole diameter of 2.313 inches and utilizes the Replacement Retaining Ring for Bulldog and Fulton Snap-Ring Jacks #FP908600 which…

view full answer...

Answer 11

Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer which…

view full answer...

Answer 12

The distance from the mounting surface to the center of the tube of the Bulldog Jack part #BD171401 measures 2-1/4 inches.

view full answer...

Diameter of Curt Round, Snap-Ring Swivel Jack Crank Tube

Product Page this Question was Asked From

Continue Researching