What Does the NC Error Message Mean on a Tekonsha P2 Trailer Brake Controller

Question

Question:

my prodigy has a read out N/C. What does that mean

asked by: Tim M

0

Expert Reply:

The NC code that you are seeing on your P2, # 90885, means that there is no trailer connected or that it thinks there is no trailer connected. There are a few reasons this could be occurring:

1. Trailer not connected to tow vehicle.
2. Trailer connected with open circuit on brake line.
3. Trailer connector disconnected or corroded.
4. Loss of trailer brake magnet ground.

The most likely is that there is corrosion build up in the vehicle or trailer side connector that needs to be cleaned out. Corrosion can also build up behind the connectors where the wires attach. This can cause the open circuit to the brake line.

You can also check to make sure the trailer brake magnets are attached to clean bare metal surfaces on the trailer. I have included a link to the installation details which has a section on the different messages the controller can display.

expert reply by: Michael H

0

Answer 1

For a basic but great brake controller the Brake EVN #TK63VR would work well in your 2013 Nissan Frontier. It would install to the factory wiring of your vehicle with the part #3050-P which plugs in under the dash. It comes with hardware to easily…

view full answer...

Answer 2

The 2006 Tundra could have been equipped with the 'Factory' hitch two different ways. If it was a dealer installed option, it would simply bolt to the frame members but if it arrived from the factory with the hitch, the hitch is tied into the…

view full answer...

Answer 3

Hey Ron Bulldog does make something like that! It sounds like you're looking for the Bulldog Round, Snap-Ring Swivel Jack #BD151464. This jack has 15" of lift, attaches using that snap-ring you mention, and has a 2,000 lb capacity. What kind…

view full answer...

Answer 4

In your 2017 Nissan Frontier, the Curt brake controller should be installed using the custom wiring adapter #C51382. This should work correctly to give you the proper wiring within your cab. Then you will use the Curt #C56226 or the Tekonsha #118266…

view full answer...

Answer 5

In order to install the Curt Discovery part #C84VV on a 2021 Nissan Frontier with factory tow package you'll simply need the Curt Custom Wiring Adapter for Trailer Brake Controllers part #C51382.

view full answer...

Answer 6

The diameter of the topwind handle on the Curt Jack part #C28304 is 1/2 inch. This is the round metal section that attaches to the crank of the jack and the red knob.

view full answer...

Answer 7

The wiring that I recommend installing on your 2019 Nissan Frontier so that you have a fully functioning 7-Way is the Tekonsha T-One #118266 because it is the most reliable option available. This comes with the wiring and relays needed for the…

view full answer...

Answer 8

You may have found the wrong connector on your 2013 Nissan Pathfinder to install the Tekonsha Plug-In Wiring Adapter #3050-P. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

What Does the NC Error Message Mean on a Tekonsha P2 Trailer Brake Controller

Continue Researching