Recommended Bulldog Trailer Jack That Installs With a Snap-Ring, 15" Lift, and 2,000 lb Capacity
Updated 10/24/2025 | Published 03/31/2025
Question:
Hi, I have a bulldog trailer jack mounted in my boat trailer. its 1000lbs rated. It’s too short, and am looking to buy something that extends more, ideally 15”. The bulldog is attached to a plate that’s mounted on the trailer. There is an o-ring snap ring that secures it to that plate. Is there a bulldog jack that I can mount to that same hole, but has a longer extension, more like 15”+? I’m looking for a 2000 lbs version ideally. Thanks.
asked by: Ron L
Expert Reply:
Hey Ron Bulldog does make something like that! It sounds like you're looking for the Bulldog Round, Snap-Ring Swivel Jack # BD151464. This jack has 15" of lift, attaches using that snap-ring you mention, and has a 2,000 lb capacity.
What kind of boat do you pull with your trailer? If there is anything else I can do for you, please feel free to drop a comment and let me know!
Product Page this Question was Asked From
Curt Round, Snap-Ring Swivel Jack - Weld On - Topwind - 15" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Topwind Jack
- 1001 - 2000 lbs
- Manual Jack
- 15 Inch Lift
- Weld-On
- With Rectangle Foot
- CURT
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: grease cap
- Search Results: junction box
- Search Results: grease cap 244
- Search Results: jack foot plate
- Search Results: hitch pin
- Search Results: ratchet binder
- Search Results: hydrastar
- Shop: BTBRV Magnetic Hitch Receiver Reducer Set - 3" to 2-1/2" & 2-1/2" to 2"
- Shop: Demco Hydraulic Brake Actuator w/ Drop and Electric Lockout - Disc - Zinc - 2-5/16" Ball - 20K
- Video: Lionshead Steel Dual Wheel Review
- Video: All You Need to Know About the Wheel Retaining Ring
- Video: In-Depth Review of the UWS A-Frame Trailer Toolbox
- Shop: 14 Gauge, 7 Conductor Jacketed Wire - Per Foot
- Shop: 12 Gauge 7 Conductor Jacketed Wire - Per Foot
- Shop: Lionshead Steel Dual Wheel - 17-1/2" x 6-3/4" - 8 on 275 mm - 8.7" Pilot - Black
- Shop: Dexter Dual Trailer Wheel Lug Nut with Swivel-Flange - Metric - Qty 1
- Q&A: Diagram of a 10k Bulldog Landing Gear Jack for Gear Replacement
- Shop: Ventline E-Z Lift Ventadome Trailer Roof Vent - Manual Lift - 14-1/4" x 14-1/4" - White
- Shop: Gooseneck Hitch
- Q&A: Looking For Replacement Swivel Jack For 1984 Scamp Trailer
- Q&A: Diameter of Center Shaft that Holds Handle on Pro Series Round Topwind Jack PS1400300303
- Video: Valterra Drip Cap and Waste Valve Cap for RV Sewer Hose: The Breakdown
- Video: Comprehensive Review: LaSalle Bristol RV Sewer Termination Adapter
- Video: The Low-Down on the Replacement Handle for Top Wind Style Trailer Jacks by Dutton-Lainson
- Video: An In-Depth Look at the Valterra Threaded RV Sink Drain
- Q&A: What is the Preferred Method of Connecting Safety Chains from a Trailer to a Trailer Hitch
- Q&A: What Is The Retracted Height Of the Curt Round Top Wind Snap-Ring Swivel Jack # C28304?
- Q&A: Solution for Installing Curt Jack # C28304 on Trailer In Place of Snap Ring that is Different Size
- Q&A: What Is The Mounting Bolt Pattern Of The Demco Hydraulic Brake Actuator DM8759122-30?
- Article: Performance Chips and Modules
on Trailer Jack
Jon G.
10/22/2025
Hey Ron, how did the Bulldog swivel jack with the 15-inch lift work out on your boat trailer? Your update could make it easier for others looking for a longer jack that still uses the snap-ring mount.