Replacement Top Cradle Assembly for a Thule Hull-A-Vator

Question

Question:

The broken part is the adjustable mechanism that sets the top cradle for the proper width for the kayak . The washer type mechanism the goes inside the groove is gone . If I buy a new cradle mechanism , will it include this part ? Also I need a new bolt [ 1 of the two that have an allen wrench head ] for the center of the cradle

asked by: Dennis D

0

Expert Reply:

The Replacement Top Assembly for the Thule Hullavator, part # 7521771001, includes the two allen wrench headed screws, but not the lower washer slide plate.

To replace the washer slide plate, you'll need part # 853593802

I've attached instructions for installing the slide plate, which you'll need to correctly reinstall the Top Assembly.

If you also need to replace the wing nut and bolt at this time, its available as part # 753-0783-08

expert reply by: Jacob W

0

click to enlarge

Answer 1

The Yakima HD Crossbars #Y01156 will work with the Thule Hullavator #TH898. Based on the pictures you sent in it looks like you have the crossbars installed upside down. The end caps have an opening on the other side that lets you easily slide in…

view full answer...

Answer 2

To attach the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs #TH898 to your 2021 Toyota Highlander you'll need a roof rack that has a T-Slot in the crossbars for the Hullavator to slide into. Currently the only brand of roof…

view full answer...

Answer 3

While two Thule Hullavators will fit the dimensions of your 68-inch wide crossbars and are compatible with the t-channels on the Yakima HD bars on the Yakima Overhaul HD #Y01151-5868, one of the things to note is that the Hullavator requires 4-8…

view full answer...

Answer 4

Hi Leon, Factory roof racks typically have a low weight capacity and won't have enough overhang for a kayak carrier with lift assist to be compatible so I definitely recommend checking the capacity and overhang to see if you can use it. The Thule…

view full answer...

Answer 5

The mounts for the older Thule Hullavators, 897 and 897XT are different than the newest iteration, the Thule Hullavator Pro Kayak Carrier #TH898. If you have the oldest version, which is the 897 (and only available from February 2005 - December…

view full answer...

Answer 6

The brackets on the Thule Hullavator 897 and the Thule Hullavator 897XT are not the same. The first generation Hullavator was designed to only work with Thule square bars, so it will not work with your Thule WingBar Evo. The updated model, 897XT, was…

view full answer...

Answer 7

Yes the Rhino-Rack Universal Load Assist - Crossbar Mount - Side Loading #RR-RUSL does fit onto the Yakima Jet Stream Crossbars that you have. This will come in handy when trying to load a kayak onto your roof when you do not have an extra set of…

view full answer...

Answer 8

I believe you're looking for a more secure hitch pin solution, in which I have just what you need! Check out the etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush #e98882 This is a locking hitch pin that will lock through your hitch…

view full answer...

Answer 9

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 10

The Thule Hullavator Pro Kayak Roof Rack and Lift Assist w/ Tie-Downs #TH898 is compatible with Thule Wingbar Evo crossbars. I reached out to the manufacturer about the fitment and they said that to use the Hullavator with the Wingbar Evo's, you…

view full answer...

Answer 11

Yes, the older Thule Hullavator (897XT) will fit Yakima JetStream bars. You'll use the T-Slot mounting hardware that would have come with the older model carrier and then you need to make sure you can move the carrier out far enough that there is…

view full answer...

Answer 12

We do have the brackets, bolts, and nuts needed to attach your Thule Hullavator 897XT to the round bars. What you need are the following parts: - Replacement Underbar Bracket #TH8535860 - Replacement M6 x 22 Carriage Bolt #915-0622-54 - Replacement…

view full answer...

Replacement Top Cradle Assembly for a Thule Hull-A-Vator

Products Featured in This Question

Continue Researching