Using the Tailgate of a Truck With a Platform Bike Rack Installed

Question

Question:

Correct me if I'm wrong but it appears to me in the demonstration video the bike rack was mounted on a double hitch receiver option piece which extends the bike rack further beyond the rear of the truck bed than if it was mounted directly to the factory installed hitch receiver on most pickups! Also, who makes a bike rack that swings to the side of the pickup bed to allow the tailgate to be lowered, does Thule make this style bike rack designed similar to the T2 Classic? Thanks,

asked by: Ken P

0

Expert Reply:

It will depend a little bit on the design of the individual truck, however the tilt-away feature of the Thule T2 Pro Xbike rack, part # TH83GC gives it quite a bit of range away from most vehicles but I can't guarantee it will clear your tailgate. I've included a video review of of this rack for you to see how the tilt-away works.

You can add locks to the T2 Pro X with part # TH450200, a two-lock OneKey Cylinder that will allow you to key the T2 alike with all of your other Thule accessories.

expert reply by: Jacob W

0

click to enlarge

Ken P.

10/2/2017

Correct me if I'm wrong but it appears to me in the demonstration video the bike rack was mounted on a double hitch receiver option piece which extends the bike rack further beyond the rear of the truck bed than if it was mounted directly to the factory installed hitch receiver on most pickups! Also, who makes a bike rack that swings to the side of the pickup bed to allow the tailgate to be lowered, does Thule make this style bike rack designed similar to the T2 Classic? Thanks,

Jacob W.

10/2/2017

Surprisingly, that's the standard shank included on the Thule T2 Classic, part # TH9044 . After you'd pointed it out I had to go out and measure it for myself, and its shank is 19 inches from the center of its hitch pin hole to the nearest part of the rack, which is one of the bike rails. This size is part of the reason that I recommended it for your truck, as it provides that much length. The long shank is a fairly common feature to a lot of Thule racks. They build it this way to provide additional space for loading the rear bike onto the carrier and to give better access to the cargo area on SUV's and Sedans when these racks are folded down. Swing away features aren't very common on platform racks, but there is a recent addition that I've found to have one of the easiest swing-away mechanisms that I've seen on a rack. The RockyMounts BackStage, part # RKY10002 is a heavy duty swing-away rack that holds bikes weighing up to 60 pounds. Its a wheel mount just like the Thule T2 Pro X, and includes integrated hitch and bike locks. It also tilts away and folds up, giving it added versatility. I've included a video of our demo team putting this swing away rack on a 2018 Chevrolet Silverado. You'll notice that this is a much smaller rack than the Thule T2 Classic, but it only allows partial access to the tailgate (at 0:20 into the video)when folded down with bikes loaded. Though, with the swing-away feature, it's likely that you'd just swing it away over tilting it. I've also included a customer picture of a fairly ingenious modification to a Toyota Tacoma that uses the swing away to access a 6-foot drawer in the truck bed. This makes the most extreme use of the rack's features.

Answer 1

Hi Joe, Thule has transitioned on most of their bike racks to clamping to the inside of the receiver tube and then using a retention pin (pictured below) that will slip into the hitch pin hole as extra security in the event that the clamp does…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Using the Tailgate of a Truck With a Platform Bike Rack Installed

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching