Bearing Kit Recommendation for BCA A17 WHL BRG Set NAT 442251 WHL Seal BCA A4 WHL

Question

Question:

Went to ORileys Auto Parts and these are the part numbers I need: BCA A17 WHL BRG Set NAT 442251 WHL Seal BCA A4 WHL BRG Set Do you have these parts? I need a set of 4 for my tandem trailer.

asked by: Pete S

1

Helpful Expert Reply:

I was able to cross reference all of the part numbers you listed and the bearing kit you need is the part # BK2-100 which has everything you need.

L44649/L68149 Bearings, 10-19 Double Lip Seal

expert reply by: Jameson C

1

Answer 1

When the L68149 bearing is paired with the L68111 race, the 10-19 grease seal is used. However when the same bearing is used with the L68110 race on a boat trailer, the #168233 seal is usually used. You can verify this by using a digital caliper to…

view full answer...

Answer 2

Since most trailer manufacturers do not make wheel and tire information available to the general public, it is hard for me to tell you what size lug nuts you have on the wheel. I can tell you they do have caps over them. The most common size of lug…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Bearing Kit Recommendation for BCA A17 WHL BRG Set NAT 442251 WHL Seal BCA A4 WHL

Product Page this Question was Asked From

Continue Researching