Various Dimensions of Dutton-Lainson A-Frame Trailer Jack, # DL22772

Question

Question:

What is the OD of the Jack, the distance from the top of the bracket to the top of the jack and the distance from the bottom of the bracket to the bottom of the tube.

asked by: Randy B

0

Expert Reply:

The Dutton-Lainson A-Frame Trailer Jack, # DL22772 has an outer tube diameter of 2-1/4 inches. It measures 10 inches from the top of the bracket to the top of the jack. It measures 10-1/4 inches from the bottom of the bracket to the bottom of the tube with the jack all the way retracted. It has a 14 inch lift.

expert reply by: Michael H

0

Answer 1

Hello Marc, thanks for reaching out. For the Dutton-Lainson A-Frame Trailer Jack #DL22772 it is going to be 10-1/4" from the mounting plate to the bottom of the jack when fully retracted. I edited a picture to help illustrate. Let me know if you…

view full answer...

Answer 2

Hey Marc. Adding a battery to the trailer is definitely the best way to power an electric tongue jack like the #EJ-3520-BBX. That said it is possible to wire it to the 7-way, and there are two ways to do this. Option 1: Add a junction box like part…

view full answer...

Answer 3

Hello again, Marc. The A-Frame Trailer Jack #DL22772 does not come with hardware. We recommend using three 3/8-16 grade 5 bolts. This is not something we carry here but you should be able to find some at your local hardware store.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Various Dimensions of Dutton-Lainson A-Frame Trailer Jack, # DL22772

Product Page this Question was Asked From

Continue Researching