Hub and Rotor Fit for Dexter Hub and Drum Assembly on Nev-R-Lube Axle

Question

Question:

i have a never lube hub on on a 8,000 lb axle and want to know if your dexter hub khr138xl9e will fit it

asked by: Dan H

0

Expert Reply:

The Kodiak hub KHR138XL9E you referenced has been discontinued. I recommend the Dexter Disc Brake Kit - 12-1/4" Hub/Rotor - 8 on 6-1/2 - E-Coat - 8K - Nev-R-Lube # K71-646-2-91 which will fit on your Nev-R-Lube axle just like the Drum Assembly # 8-389-81UC3.

If you need further recommendations, please let me know and I'd be happy to assist.

expert reply by: Jason S

0

Answer 1

Hey Tim, the Brandmotion FullVUE Digital Rear View Mirror with HD Backup Camera #BM86YR that you referenced does come with a camera in the third brake light/CHMSL location that you asked about. I attached a picture that shows the contents of the kit…

view full answer...

Answer 2

Hey Michael, The Brandmotion FullVUE Rear View Mirror #BM86YR is a confirmed fit for your 2025 Ram 3500. I reached out to the manufacturer as well just in case and they confirmed this is a direct fit for your vehicle and will work well! I went ahead…

view full answer...

Answer 3

Yes, you can use the Reese Friction Sway control part #83660 without a weight distribution system. You would just need to use the tab part #RP26003 on the ball mount as well.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Hub and Rotor Fit for Dexter Hub and Drum Assembly on Nev-R-Lube Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching