Can I Drill Holes in the Brackets of the Trailer Hitch Receiver to Match RV Frame Holes?
Updated 01/23/2020 | Published 09/08/2017
Question:
C13701 curt adjustable hitch The video for this item number c13701 says the holes are drilled in the mounting brackets at 8 and 5/8 inches on center To avoid drilling new holes in my RV frame may I simply drill new holes in the hitch mounting brackets? I ask this because my RV has predrilled frame holes on 6.5 inch centers. If I may do this I wont have to drill two new holes in my RV frame
asked by: Ray N
Expert Reply:
I definitely see the logic in drilling holes in the mounting bracket of the Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2" # C13701 versus the frame of your RV, however it isn't that easy. If you were to move the bracket attachment holes, then you would minimize the weight capacity and stability of the trailer hitch receiver as well as void the warranty on the hitch.
The installation would be easier for sure, but I can't recommend going this route as the tongue weight capacity of the hitch would be most effected and would greatly inhibit your ability to carry or tow with this hitch.
Product Page this Question was Asked From
Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2"
- RV and Camper Hitch
- Frame Mount Hitch
- 500 lbs TW
- 5000 lbs GTW
- 18 - 51 Inch Wide Frames
- Towing and Cargo
- Bolt-On
- Weld-On
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: brake controller
- Search Results: bracket
- Search Results: trailer wiring
- Shop: Brake Controller
- Shop: TowSmart Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt No-Drill Bracket for 6-Way or 7-Way Round Trailer Connector Mounting Bracket - Long
- Q&A: Wiring And Brake Controller Needed For A 2006 Chevy Express Van 1500
- Video: Let’s Check Out the Curt Universal Installation Kit for Trailer Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: TowSmart Converter w/ 5-Way Flat Trailer Connection - Vehicle End
- Shop: TowSmart ProClass Multi-Tow 7-Way and 4-Way Flat Trailer Connector - Vehicle End
- Shop: Front Mount Hitch
- Shop: Curt No-Drill Bracket for 4-, 5-, or 6-Way Trailer Connector Mounting Brackets - Short
- Shop: Curt Easy Mount Bracket for 4- or 5-Way Flat and 6- or 7-Way Trailer Connectors - 2" Hitch
- Search Results: 4 pin bracket
- Search Results: 18136 mount bracket
- Search Results: 18136
- Search Results: 18144
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Will the No-Drill Bracket part # 18136 Work on a Round Hitch
- Video: Brophy Mounting Bracket for 4-Pole Flat Trailer Connector: The Breakdown
- Shop: Suspension Enhancement
- Video: EZ Connector Wiring 319-S7-60F Review
- Video: Setting up the etrailer Trailer Hitch Receiver on a 2019 Nissan Frontier
- Q&A: Solution for Installing Trailer Hitch Where Bolt Holes Don't Seem To Line Up
- Video: Feature Breakdown: Bauer Products 4-Way Trailer Plug Holder
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2013 Nissan Frontier C56225
- Q&A: Can I Use a 4 Way Vehicle Connector with 7 Way Adapter and the Curt Echo Brake Controller?
on RV and Camper Hitch
Boots
1/23/2020
Can I drill 2 small self taping holes in hitch to mount bracket for camper plug