Replacement Grease Zerk for EZ Lube Spindle

Question

Question:

WHAT IS SIZE OF ZERK ON END OF 3500 EZ LUBE SPINDLE TO REPLACE IF BENT OR BROKE

asked by: BRAD

0

Expert Reply:

The grease zerk used in their EZ Lube spindles like # TRU74FR is a standard 1/4-inch pipe thread fitting that you can replace with an item like # Gzerk. Your local hardware store may have one too. You can use a grease gun kit like # L30132 on this fitting.

expert reply by: Adam R

0

Answer 1

You should have a standard 1/4" grease zerk fitting on your EZ Lube spindles. The 1/4" zerk is a fairly common size so you should be able to easily acquire one. We actually have the Powerbuilt Pistol Grip Grease Gun #ALL940798 which would…

view full answer...

Answer 2

To answer your question...yes, you can rip off the zerk fittings of your spindles so that you could install Bearing Buddies. But you should note that Bearing Buddies commonly allow people to overfill their hubs with grease which then turns into a…

view full answer...

Answer 3

When you are replacing bearings you do want to pack them prior to installing the new ones into your hub. This ensures that the grease actually gets pushed completely into the bearings so that they work properly and don't overheat. You can use a…

view full answer...

Answer 4

The zerk fittings on the Dexter Trailer Axle #T3584F-EZ-8974 are a 1/4" pipe thread. If you need a replacement zerk fitting you can use part #Gzerk, which we have confirmed to fit the Dexter Ez-Lube Axles.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacement Grease Zerk for EZ Lube Spindle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching