Fit of Curt Hitch Lock on Toyota Tundra

Question

Question:

Will this fit a 2017 Toyota Tundra 5.7 Crewmax 4X4? My current pin lock from my old vehicle is just a little short to use.

asked by: Robert T

0

Expert Reply:

Pin locks do not fit specific vehicles such as your 2017 Toyota Tundra, but the Curt Hitch Lock # C23519 you referenced will fit so long as your receiver is 2" or 2-1/2" with a pin hole diameter of 5/8". The lock is 6" overall with a usable pin length of 3-5/8" so there is plenty of length for you to work with.

I've attached a link to a review video of this lock for you to take a look at.

expert reply by: Kyle S

0

Answer 1

Hey Hugh! That is correct, if someone wanted to pull the pins out and steal the ball platform on the B&W Tow & Stow 2-Ball Mount #BWTS10033B they could. If you want to secure the dual ball platform you will need to add the InfiniteRule Hitch…

view full answer...

Answer 2

Hello Hal, Great question! It really would be nice if Toyota kept their receiver the same size as everyone else’s so any standard 2" lock would fit. The good news is that Infinite Rule actually made a lock specifically for the 2024+ Toyota…

view full answer...

Answer 3

I recommend the etrailer Hitch Receiver Lock for 2" and 2-1/2" Hitches - Flush - 3-5/8" Span - Chrome Item #e98881 for your 2019 Toyota Tundra.

view full answer...

Answer 4

For an anti rattle hitch lock to fit the wider hitch on your 2016 Toyota Tundra the best option is the Anti-Rattle Trailer Hitch Lock #63232 which has a usable span of 3-1/2 inches or even the #SHP2040-XL for a 3-7/8inch span. I attached a review…

view full answer...

Answer 5

When determining what rise/drop to use on a B&W Tow & Stow, it is important that your trailer connection is as level as possible. The first thing you need to do is measure the height of your hitch receiver from level ground to the top inner…

view full answer...

Answer 6

The Curt Hitch Lock part #C23519 has a usable pin width of 3-5/8" which should be plenty for your 2019 Toyota Tundra. However, if you wanted to be absolutely certain you would just need to measure the receiver tube (outside to outside) where the…

view full answer...

Answer 7

I went through our reviews and wasn't able to find any Tundra owners that experienced an issue with the Bolt Trailer Hitch Receiver Lock #BL7023584 interfering with the safety chain loops on the factory hitch, which is what I assume you're…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Maurice, Thule offers the TracRac SR which mounts in the stake pockets so that you still have the cantilever and don't have to remove your deck rail system. If your Tundra doesn't have the stake pockets then the installation will require…

view full answer...

Fit of Curt Hitch Lock on Toyota Tundra

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching