Hardware Needed for Replacing Wobble Rollers on Boat Trailer
Updated 03/26/2020 | Published 08/07/2017
Products Featured in This Question
Question:
I need to replace all the wobble rollers on a very old boat trailer. I have a couple questions: 1 Are these shafts too rusty to allow the rollers to turn? 2 How important is it that the replacement rollers are exactly the same size? The old ones are 4 3/4inch wide and 4 1/4inch in diameter, but the only rollers I see on your site that fit a 5/8 shaft are 3inch wide and 5inch diameter. 3 What other hardware do I need to order to install the new rollers? Thank you!
asked by: Elizabeth A
Expert Reply:
The shafts in your picture do look a bit rusty but most likely they will still work. But you have to inspect them all to make sure they only have surface rust.
You'll also need the washer part # CE10982 and the retainer ring part # CE10981 to install the wobble roller part # YR530R-5P you mentioned.
Product Page this Question was Asked From
CE Smith Wobble Roller Retainer Ring - Zinc-Plated Steel - Qty 1
- Accessories and Parts
- Boat Trailer Parts
- Hardware
- Retaining Ring
- CE Smith
more information >
Continue Researching
- Search Results: boat trailer parts
- Search Results: tongue cover
- Video: CE Smith Deep V Keel Roller Assembly for Boat Trailers Review
- Shop: CE Smith Deep V Keel Roller Assembly for Boat Trailers - Galvanized Steel/Black Rubber - 12"
- Shop: CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 9" - Qty 4
- Search Results: tire chains
- Shop: CE Smith U-Bolts - Galvanized - 3-13/16" Long x 3-1/16" Wide x 1/2" Diameter - Qty 4
- Shop: Caliber Bunk Wrap Kit for 2x4 Boat Trailer Guides - 24' Long - Light Gray
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: Can Cotter Pin Be Used to Secure Yates Ribbed Wobble Roller YR343R-6P
- Shop: Yates Y-Style Bow Stop for Boat Trailers - TPR - 5-3/4" Span - 1/2" Shaft - Yellow
- Shop: CE Smith Wobble Roller Washer for 3/4" Shaft - Zinc-Plated Steel - Qty 1
- Shop: CE Smith Wobble Roller Retainer Ring - Zinc-Plated Steel - Qty 1
- Q&A: Hitch And Bike Rack For Carrying Two Lectric XP4 Ebikes On A 2016 Chrysler 200
- Q&A: Wobble Roller, Hog Ring and Washer for an EZ Loader Boat Trailer
- Q&A: Replacement Wobble Rollers 5 Diameter, 3 Wide For a 3/4 Shaft
- Q&A: Recommended Replacement for Shelby 5460A Trailer Winch
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: How To Install New Wobble Rollers, Washers, And Retaining Rings
- Q&A: Differences between Yates Keel Rollers # YR12000 and # YR12244-125EC
- Article: Most Popular Wheel Bearings
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: Boat Trailer Guides: Which are the Best?
- Article: Cargo Tie-Down Methods
- Article: Adding Electric Over Hydraulic Disc Brakes
Troy S.
3/25/2020
My current wobble rollers are in need of replacing. The measurements are:1” shaft 3” wide4 1/2 diameterWould you inform me as to what size I can use? Can’t seem to find the above measurements? I have pictures! Need to prefer ASAP!