Replacement Bracket Kit Recommendation for Firestone Air Bag Kit F2071

Question

Question:

is there a complete replacement bracket kit for F2071?

asked by: Gilbert

0

Expert Reply:

The replacement brackets you'd need for the # F2071 are the part # F5376 (quantity 2) for the upper brackets, part # F5092 (quantity 2) for the lower brackets, # F5086 (quantity 4) for the bracket straps, and part # F5093 (quantity 4) for the other bracket straps.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

Hello Barry, Since you already have a weight distribution (WD) hitch and are only experiencing a little rear sag, I recommend going with SumoSprings. I typically only suggest Timbrens for those who are towing heavy loads regularly, as they can create…

view full answer...

Answer 5

Hey Gary. The Draw-Tite Front Hitch item #65031 is going to mount a bit higher on your 2004 Toyota Tundra compared to the Curt item #31180. The Curt Front Hitch item #31180 is 14-3/4" off the ground when measured from the top of the inside of…

view full answer...

Answer 6

Hi Mitchell, Great question, and I’m glad you’re double checking this before jumping in because with a 3–4 inch lift, that’s exactly where fitment can get tricky. Even though the brackets may look similar to Air Lift Ride-Rite kits, the Pacbrake part…

view full answer...

Answer 7

Hello, Russ. The Firestone Ride-Rite Air Helper Springs #F2071 is indeed the kit you need for a 1999 Dodge Ram 3500 4WD Club Cab Diesel with the long bed. Keep in mind this kit is not compatible if you have an in-bed 5th wheel or gooseneck hitch.…

view full answer...

Answer 8

Hey Bryon, Yes, even when the air springs are deflated down to the 5psi users have noted that there is still a difference in the unloaded ride quality. The severity of that difference depends on a lot of different factors, but I've mostly seen…

view full answer...

Answer 9

The correct size lift spacer you will need for your Firestone Ride Rite airbags depends on how much the BDS Lift Kit will lift the rear of the vehicle. If the kit lifts the rear of your truck by 3 inches, then you would want a 3 inch spacer, #F2367.…

view full answer...

Answer 10

Installing the #F2703 on your 2012 F-250 will require moving the block in your picture. However, I'm not sure if it can be moved to the top of the jounce stop since we don't have any information on it and neither did Firestone. I recommend…

view full answer...

Answer 11

Yes sir, I'd add an airbag kit to the rear axle to assist with leveling out the truck and trailer, and reducing some back and forth sway on turns and bumps. The Firestone setups tend to hold up a bit better, so I'd go with the Firestone…

view full answer...

Answer 12

Hey Darrin, yes the Timbren suspension enhancement kit part #TFR250SDE that you referenced does fit your 2004 Ford F-250 with a Knapheide utility bed and will do a great job to reduce suspension sag. I will say that these are not designed to fix…

view full answer...

Replacement Bracket Kit Recommendation for Firestone Air Bag Kit F2071

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching