Needing a 6 Inch Winch Handle to Fit a Dutton-Lainson DL1100 Winch

Question

Question:

I need 6inch handle for DL1100 I ordered a 6 inch handle and it was the wrong slot size.

asked by: Marc H

0

Expert Reply:

The replacement 6 inch winch handle for the Dutton-Lainson Hand Winch-Single Speed -1,100 lbs, # DL15103, will be # DL5703657.

This handle is confirmed to fit the Dutton-Lainson DL1100A winch.

expert reply by: Jared P

0

Answer 1

We do have a short 6 inch handle that will work with the model DL200A Dutton-Lainson Hand Winch #DL14725. The correct part is the Replacement Winch Handle for Dutton Lainson Winch - 6" #DL70336.

view full answer...

Answer 2

The Replacement Winch Handle for Dutton Lainson Winch, part #DL70336 is designed to fit Dutton-Lainson winches like part #DL15502. I went to our warehouse and measured the #DL15502 shank the handle fits. The shank measures .46 X .625 inches. I have…

view full answer...

Answer 3

Hi Scott; the Dutton-Lainson Hand Winch #DL17000 would be a good replacement for the DL1100A. However, the mounting bolt pattern on the bottom isn't an exact match so you might have to move your mounting bolts depending on how they're…

view full answer...

Answer 4

I went out to our warehouse to take a look at the Dutton-Lainson Hand Winch - 1,100 Pounds #DL15103 referenced in your question. I was able to take the measurements you are needing and have attached an image with these dimensions labeled that you can…

view full answer...

Answer 5

If it was a 4-pin connector with 5 wires then it is called a wishbone harness and would have 2 wires attached to the running light pin so you have one wire for each side of the trailer. Typically, on a 4-Way, the white wire is ground, brown is…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Needing a 6 Inch Winch Handle to Fit a Dutton-Lainson DL1100 Winch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching