Replacement Steps for 2016 Lance 1172

Question

Question:

Looking for replacement steps to fit a 2016 Lance 1172. 2 steps to be bolted to existing holes. Approx 7 inch by 19.25 inch on center bolt pattern. Can you make a recommendation? Thx

asked by: Chris C

0

Expert Reply:

The steps we carry that are the closest to your mounting hole measurements are the Flexco Manual Pull-Out Steps # SMFP-2120. The mounting holes are 20-1/2 by 7 inches.

Unfortunately, there aren't any steps that we carry that are exactly the same measurements as yours.

expert reply by: Charles S

0

Answer 1

The mounting brackets for the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear item #TLA7833 measure 21-1/2" wide x 12-1/2" tall x 8-1/2" deep. The steps will bolt directly to your Lance 2021 1172 Truck Camper with…

view full answer...

Answer 2

Hi David, thanks for reaching out! The older Go Power PWM-30 Solar Controller has been discontinued, but you can use the Go Power PWM Solar Charge Controller with Bluetooth #GP76QR along with the Installation Adapter Plate #GP86QR to replace it! I…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Replacement Steps for 2016 Lance 1172

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching