Recommended Dust Cap with 3.125 Inch Diameter

Question

Question:

We are a AG spreader equipment MFG. Looking for a GKN 1609 style dust cap, 3.122-3.125 OD but with a longer flange. need .3125 or so.

asked by: Randy D

0

Expert Reply:

The closest grease/dust cap we have available to the dimensions listed in your question is the Fulton Grease Cap # F001609. This cap has an outer diameter of 3.125 inches and a flange length of 0.296 inches.

I have attached a short video demonstration on this product for you to check out.

expert reply by: Chris R

0

Answer 1

The Replacement Base Legs for Curt A16 5th Wheel Trailer Hitch #C16920 are NOT compatible the E16 head #C16515. Although they may bolt up Curt says are not compatible. You will need to either upgrade the head to the A16 #C16520 and use the A16 legs…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Recommended Dust Cap with 3.125 Inch Diameter

Featured Help Information

Miscellaneous Media

Continue Researching