Recommended 2-Inch Trailer Hitch Ball For Class l Trailer Hitch Ball Mount

Question

Question:

can i get a 2 inch ball for a class 1 ball mount

asked by: Rich

0

Expert Reply:

A Class l trailer hitch ball mount typically uses a hitch ball with a 3/4 inch shank.

If that is the case for your ball mount then I recommend a hitch ball like part # C40018.

expert reply by: Jeffrey L

0

Answer 1

Hey Tony, Definitely smart to verify the right kit for your 2024 Toyota 4Runner, and I'll go ahead and list out exactly what you need: - Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness #RED82CR This comes with the controller, wiring…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, David you are correct. The Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness item #RED82CR is exactly what you need. Since your 2024 Toyota 4Runner came with a 7-way connector, the plug and play adapter included with item #RED82CR will…

view full answer...

Answer 5

The load range tire used is going to depend on the gross trailer weight capacity, which should be on a sticker or plate near the front of the trailer frame or in the trailer's literature. It probably also indicates the load range, or at least the…

view full answer...

Answer 6

Possibly! It depends on the dimensions of the rear cargo area. I don't have a 2018 Toyota 4Runner in front of me, and all I can find online is cubic feet, but I can tell you that the Yakima MOD HomeBase SUV Storage Drawer item #Y55DJ measures…

view full answer...

Answer 7

Based on the measurements you took on your trailer hitch and trailer coupler, you will technically need a ball mount that features a rise of around 8-1/2 inches for a completely level setup. Between the two ball mount options you mentioned, the Curt…

view full answer...

Answer 8

The thickness of the platform on the Curt Class I Drawbar #C45021 where the hitch ball is installed is about 5/8". I have attached a photo to demonstrate this and you can see this referenced in the attached review video. For a 2" hitch ball…

view full answer...

Answer 9

There are options to install a trailer hitch on your 2004 Volvo XC70 but the only fits for this vehicle are Class II hitches with a 1-1/4 inch receiver and they do not allow weight distribution to be used; I checked with the hitch manufacturers to…

view full answer...

Answer 10

I searched your owners manual and could not find any reference to ensure your rear bumper on your 1999 Toyota Tacoma is rated for towing. Because of this I recommend installing a etrailer Trailer Hitch Receiver #e64AR. This will ensure you do not…

view full answer...

Answer 11

I took a look at the online version of the owner's manual for your 2018 Ford F-150 and was able to locate the wiring color code for the factory 7-Way trailer harness on the truck. The wires leading up to the factory plug are as follows: Yellow -…

view full answer...

Answer 12

When we installed the Draw-Tite #24796 on a 2009 Nissan Maxima, we found that the hitch height and the setback was the exact same as the Curt #C11352 you referenced. This being said, the Euro-style ball mount won't work with the Draw-Tite hitch.…

view full answer...

Recommended 2-Inch Trailer Hitch Ball For Class l Trailer Hitch Ball Mount

Product Page this Question was Asked From

Continue Researching