Will Swivel Jack Handle Move When in Stowed Position?
Updated 06/30/2017 | Published 06/29/2017 >
Question:
When the jack is folded for travel, will the handle free float down or is it stiff enough to stay away form the road side? I am trying to decide if a top winding handle would be better for storing so the road does not hit the handle while driving.
asked by: Peter C
Helpful Expert Reply:
The handle for the Square Pipe Mount Swivel Jack, # TJDP-7000S-B, is going to be stiff enough that it will not free float. For example, if you refer to the picture I've attached, you can see the handle sitting in an upright position. You can also take a look at the video I've linked, and at about the 1:30 mark, you will be able to see the handle being used and then come to a stop without falling back down
Product Page this Question was Asked From
Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Sidewind Jack
- 6001 - 7000 lbs
- Manual Jack
- 28 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: square trailer jack
- Video: A Closer Look at the Square Pipe Mount Swivel Jack w Footplate
- Video: Breaking Down the Round, Pipe Mount Swivel Jack w/ Footplate
- Video: etrailer and Bulldog Topwind Jack Side By Side Comparison
- Video: Breaking Down the Square Pipe Mount Swivel Jack w Footplate
- Video: Let’s Check Out the Square Pipe Mount Swivel Jack w Footplate
- Video: An In-Depth Look at the Round, Pipe Mount Swivel Jack w/ Footplate
- Q&A: Recommended Swivel Bolt-On Trailer Jack for Pop Up Camper
- Q&A: Recommended Weld-On Swivel Jack to Fit a 20 Ft. Triton Boat Trailer
- Q&A: Trailer Jack To Support 6X12 Trailer Weighing 2,500 Plus Pounds
- Q&A: 7k Trailer Jack Recommendation for Enclosed Trailer
- Q&A: Topwind Trailer Jack vs. Sidewind Trailer Jack for A-Frame Trailer
- Q&A: Recommendation for Pipe-Mount Swivel Trailer Jack that has a Grease Fitting
- Q&A: Solution for Replacing Ram Swivel Jack with Jack that Has Wheel Caster
- Shop: Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Sidewind - 28-1/2" Lift - 7K
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Topwind - 10-5/8" Travel - 7,000 lbs
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 15-1/2" Travel - 7K
- Shop: Square Pipe Mount Swivel Jack w Footplate - Drop Leg - Weld On - Topwind - 28-7/8" Lift - 7K
- Shop: Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Topwind - 15-1/4" Travel - 7K
- Shop: etrailer Swivel Jack w/ Bolt-On Mounting Plate - Sidewind - 10" Travel - 3,000 lbs
- Shop: Square Pipe Mount Swivel Jack w/ Footplate - Weld On - Topwind - 15-1/2" Travel - 3,000 lbs
- Video: Detailed Breakdown of the Replacement Top Cap for Dutton-Lainson Jacks



