Replacement Rubber Pad Recommendation for Yakima Railgrab

Question

Question:

hello. i am trying to find replacement rubber pads for my older yakima rail grab towers. i cant tell exactly which is the right set, but i can send a photo of my existing ones.

asked by: Phil

0

Expert Reply:

Sounds like you are looking for the Replacement Pads for Yakima RailGrab Roof Rack Towers # Y8880147.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We have a few options for replacement pads for Yakima roof racks like item #Y8810008. They are organized by what specific tower they go to. I have linked our entire selection below. If you would like to email me back some information on yours like a…

view full answer...

Answer 2

In order to find a local dealer for installation purposes, there is a way for you to input your location in order to find dealers close to you. That location for this information is right below the product images and videos. Underneath those…

view full answer...

Answer 3

Hey Cliff Man! While the q towers have been discontinued by Yakima few years back, you can still get replacement vinyl pads - Replacement Vinyl Pads for Yakima Q Clips (QTY 2) #Y8810072. These go between the towers and the roof to prevent scratching…

view full answer...

Answer 4

A roof rack for your 2016 Ram 1500 Crew Cab would be your best option for carrying a kayak. The Rhino Rack Aero Kit part #RRVA150B-2, #RRRLKVA, and #DK043 would be a fantastic option that's confirmed as a fit for your truck for carrying a kayak…

view full answer...

Answer 5

In order to haul kayaks on a 2018 Ram 2500 with RamBox you'll need to place them on the roof with a roof rack and roof mounted kayak carrier. The reason for this is that no one makes a ladder rack that will work with the RamBox. For a roof rack,…

view full answer...

Answer 6

We do! What you need is the Replacement Rubber Pads for Yakima Railgrab Claws #8880146 and you're set.

view full answer...

Answer 7

The Yakima RailGrab Towers for Flat and Raised Side Rails (QTY 4) #Y00138 come with all of the padding necessary. If the padding has worn down or is missing from your Yakima RailGrab towers, then the Replacement Pads for Yakima RailGrab Roof Rack…

view full answer...

Answer 8

We do carry replacement parts for the Yakima Railgrab foot. For the claw base and nut you would want the part #Y8880279. The medium claws are no longer available. For the claws with pin adapters you would want the part #Y8880201. For replacement…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Rubber Pad Recommendation for Yakima Railgrab

Product Page this Question was Asked From

Continue Researching