Trailer Hitch Recommendation for a 2011 Mazda 3 Sport Hatchback for Use with a Bike Rack
Updated 05/31/2017 | Published 05/30/2017
Products Featured in This Question
Question:
Hi, what I have a Yakima holdup 2inch bike rack that I want to install on my 2011 Mazda 3 hatchback. Should I go Curt or Drawtite? And which adapter would fit?
asked by: Christopher
Expert Reply:
I will be happy to make some hitch recommendations for your 2011 Mazda 3 Sport hatchback. I recommend Draw-Tite trailer hitch # 24843. The reason I recommend it over the Curt option is because with Curt you would have to use stabilization strap # 18050 when using the hitch with your bike rack per the Curt warranty requirements. Draw-Tite does not have that requirement.
While there are 1-1/4 to 2 inch adapters that would work there are a couple of problems. First, the use of an adapter is prohibited by Yakima and voids the rack warranty. The other problem is that adapters reduce the tongue weight capacity of a trailer hitch by 50 percent. The hitches for your Mazda 3 have a tongue weight capacity of 200 pounds. An adapter would reduce that to 100 pounds. The bike rack weighs about 49 pounds leaving just 51 pounds for the bikes.
The best solution is to replace the spine (which is the part with the shank) but also will require a different hitch. If you have a first or second generation HoldUp (silver) then you can use spine # Y80126. If you have a newer model (black) then use spine # Y8890278. But in order for this to work you would have to use Curt trailer hitch # C11383 because the shanks for the 1-1/4 inch HoldUps do not fit the Draw-Tite hitches properly.
I know this is a little complicated so if you have additional questions just let me know.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch ball mount
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Suspension Enhancement
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: Comparing the Curt Hitch C13416 and EcoHitch Hitch 306-X7396 for a 2019 Toyota RAV4
- Shop: Brake Controller
- Video: Clean Up Your Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Shop: Base Plate for Tow Bar
- Q&A: Trailer Hitch and Wiring for 2027 Kia Telluride
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer jack
- Shop: Roof Rack
on Trailer Hitch
