Are Lippert Groujnd Control 3.0 Landing Gear Legs Round Or Square
Updated 05/30/2017 | Published 05/26/2017
Question:
do the front landing gear jacks replace the existing landing gear to the same internal brackets that they are mounted to? Are the new landing gear round tubular in shape or square like the original landing gear. Thanks
asked by: Cort L
Expert Reply:
The rear jacks for the Lippert Ground Control 3.0 # LC358590 are made with a round tube design.
The front jacks are made with a square tube design and mount to the existing weld stops on your trailer frame. I have attached a drawing that shows the dimensions of the tabs on the frame measure 15-1/2 inches between the tabs and are 17-1/2 inches outside to outside dimension.
Product Page this Question was Asked From
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Camper Jacks
- 5th Wheel Camper
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- 36 Inch Lift
- Bolt-On
- 4 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Bluetooth Control - 6-Point Set
- Shop: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
- Search Results: lippert camper jacks
- Search Results: 50 amp breaker
- Shop: Derale Automatic Resetting Circuit Breaker - 50 Amp
- Shop: Circuit Breaker - 50 Amp - Perpendicular Mount Bracket - Cycling Auto Reset - Plastic - Type I
- Video: Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System Installation - 2020 Forest River Ch
- Video: How to Install the Lippert Ground Control 5th Wheel RV Leveling System - 2015 Forest River Vengeance
- Q&A: How Much Room on RV Frame Does Lippert Ground Control Middle and Rear Jacks Take Up
- Q&A: Clearance Required Around Rear Jacks of Lippert Ground Control 3.0
- Q&A: 6 Point Automatic Leveling System Recommendation 2010 Keystone Montana Fifth Wheel
- Q&A: Solutions To Add More Clearance For Lippert Ground Control 3.0 Jack Legs
- Q&A: How to Determine if Lippert Ground Control 3.0 Will Fit 5th Wheel RV
- Q&A: Mounting Plate Height of Replacement I-Beam Jack Bracket for Lippert Ground Control
- Q&A: Can Rear Jacks of Lippert Ground Control be 24 inches From Rear Axle
- Search Results: trailer jack
- Video: Review of MORryde Camper Jacks - I-Beam Mounted Stabilizer - MR96RV
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Shop: MORryde I-Beam Mounted Stabilizer for 5th Wheels and Travel Trailers
- Search Results: camper jacks
- Video: All You Need to Know About the Landing Gear Set
- Article: What are the Common Types of Propane Fittings Used on RVs?
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Shop: etrailer Electric Trailer Jack - Drop Leg - A-Frame - 18" Lift - 5,000 lbs
- Video: etrailer Electric A-Frame Trailer Jack Detailed Breakdown
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Article: Converting Your RV Water Heater to Tankless
- Shop: Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
- Video: Review of the Replacement Front Jack for Lippert Ground Control 3.0 Leveling System
