Recommended Air Helper Springs for a 2016 Nissan Titan XD

Question

Question:

i have a 2016 nissan titan xd diesel getting fifth wheel rv and wondering how the air bag work to add goose neck hitch pin weight

asked by: Bob M

0

Expert Reply:

There are 2 options from Air Lift for you to add Air Helper Springs on your 2016 Nissan Titan XD with the OEM gooseneck hitch. The LoadLifter 5000 # AL57229, and the LoadLifter 5000 Ultimate with Internal Jounce Bumpers # AL88229.

Either of these Helper Springs has a weight capacity of 5,000 lbs but will not increase your XD's weight-carrying capacity. You will want to be sure that you are not exceeding the recommended weight limit from the manufacturer.

A compressor system like the Air Lift WirelessONE # AL25980 will allow you to adjust your air springs from inside or outside of your cab by using a hand-held controller. It will also automatically maintain the pressure level that you pre-set on it.

expert reply by: Jon G

0

Answer 1

The Air Lift LoadLifter 5000 Air Helper Springs part #AL57229 are a confirmed fit for a 2016 Nissan Titan XD 2WD. These air springs offer a bolt-on fit without any drilling required. They will provide rear end support for towing or hauling. They can…

view full answer...

Answer 2

The Timbren Suspension Enhancement System part #TNRTTNA is a great option for a 2017 Nissan Titan XD. It should engage fully with that amount of tongue weight so there should not be any pogoing but then again, this is not something that we can really…

view full answer...

Answer 3

Let's start with the rear suspension help for your 2018 Nissan Titan XD, and for the best overall support I do recommend air bags for your truck, with the correct fit being the Firestone Ride-Rite Air Helper Springs #F2594. These air bags - which…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...