Dimensions Of Dutton-Lainson Hand Winch Mounting Holes

Question

Question:

Can you forward the specs for the mounting holes or tell me where I can find. Shelby 5408 winch mounting holes Thanks

asked by: Scott

1

Helpful Expert Reply:

We don't carry the Shelby 5408 winch, but from what I see they are the same mounting holes as the Dutton-Lainson Hand Winch with TUFFPLATE Finish, Two Speed with Direct Drive - 3,200 lbs # DL15440. I've attached a picture of those measurements for you.

expert reply by: Jason S

1

click to enlarge

Answer 1

Hello Tom, thanks for reaching out. The diagram below will show you the dimensions of the mounting hole pattern and base plate size for the Dutton-Lainson Hand Winch #DL14725.

view full answer...

Answer 2

The bolt hole spacing as well as the bolt hole pattern is different when you compare the #DL14627 (which is the 1802A) to the #DL15440 (3200A). The overall dimensions differ as well. I am attaching some pictures showing the bolt hole measurements as…

view full answer...

Answer 3

Hey Chris, I recommend checking out the Dutton-Lainson Hand Winch w/ Automatic Brake #DL15761 which has a slightly higher weight rating at 2,500 lbs and has a 9-3/8" long handle. The handle is a bit long, but it's positioned on one end of…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Dimensions Of Dutton-Lainson Hand Winch Mounting Holes

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching