Recommended Dust Cover Plugs For Dexter Brake Assemblies

Question

Question:

Hi, I purchased a set of dexter e brakes 23-464 and 23-465. Do you carry a dust cap for adjustment opening? Thanks

asked by: Nirbhai B

0

Expert Reply:

The dust caps for the adjustment opening on your Dexter brake assemblies I recommend are the Adjuster Plugs for 7", 10", and 12" Brake Assemblies - Qty 4 # BP10-220. These will work great with your assemblies.

expert reply by: Jason S

0

Answer 1

Hello again Nick; the PingMaster 5000 Wireless Trailer GPS Tracker #PM74FR is a sealed unit and not designed for battery replacement. The battery lasts years, and the entire unit would be replaced at the end of its lifespan. What will you be using…

view full answer...

Answer 2

Yes we have the Redarc In-Vehicle BCDC Battery Charger #RED96FR which essentially is the same thing as the charging system you referenced as it gives you a way to enhance the charging circuit ran to your 7-way to put the best charge on the trailer…

view full answer...

Answer 3

Hi David; this is pretty common and all you really need is to throw in some simple diodes #RM-690. These will only allow power to flow in one direction so it will stop any backfeeding and power drain. It sounds like everything is in-line so you can…

view full answer...

Answer 4

If you have a self-adjusting brake assembly, you'll be able to see the adjuster cable extending across the brake assembly once you remove the hub/drum. However, we sell the Dexter brake kit #K23-463-00, so we can confirm the brakes are not…

view full answer...

Answer 5

I would not recommend using fuses instead of a circuit breaker when installing a brake controller like the Primus IQ #TK90160. While it does protect the circuit it also totally kills the circuit till the fuse is replaced. A breaker will reset…

view full answer...

Answer 6

The optional LED you see in the install diagrams for the Redarc BCDC Charger part #331-BCDC1240D is just an indicator light to let you know it's charging. It does not show anything beyond it being off or on.

view full answer...

Answer 7

The distance you'll be measuring for fitment of the Fastway ONEstep Wheel Chocks is where the chocks will actually be installed as you can see in the attached photo. If that distance is between 16" - 24" then use part #FA84-00-4840 but…

view full answer...

Answer 8

Yes, the Dexter Electric Trailer Brake Assembly #23-181 must be oriented so the brake shoe pin is at the top and the adjusters are at the bottom. This is also only for mounting on the right side of your axle. We have the Assembly #23-180 for the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Recommended Dust Cover Plugs For Dexter Brake Assemblies

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching