Thread Pitch of Hardware that Comes with Draw Tite Hitch 75105

Question

Question:

I am installing a draw-tite # 75105 on a 2002 Tundra. Weld s on the frame are rusted bad. I know this is a 12mm thread, but what is the thread pitch? So I can get a tap to chase the threads. Thanks !!

asked by: Ryan S

0

Expert Reply:

The threads of the bolts that come with the 75105 are12mm X 1.25 mm pitch threads. This is an extra fine metric thread. You would need a tap with that thread pitch.

I attached a help article on cleaning weld nuts for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I looked up the towing capacity for the 2000 Toyota Tundra and it ranges between 4,950 to 7,200 lbs (please confirm with your owners manual). If you are looking for a hitch that includes the bolts and no drilling required for installation, I…

view full answer...

Answer 2

According to the installation instructions for the Draw-Tite Max-Frame Trailer Hitch Receiver part #75105 which is a fit for your 2004 Toyota Tundra, the kit comes with the following: (4) - 12mm Hex Bolts (4) - 1/2" Serrated Washers (2) - Bolt…

view full answer...

Answer 3

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75105 is a confirmed fit for 2000-2006 Toyota Tundra models with or without factory towable bumper. It is very possible that the manufacturer used different nut and…

view full answer...

Answer 4

The Draw-Tite Max-Frame Trailer Hitch Receiver part #75105 is a confirmed fit for your 2006 Toyota Tundra as long as you are willing to remove the factory hitch if equipped. I went out to our warehouse and measured the overall dimensions for you…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Thread Pitch of Hardware that Comes with Draw Tite Hitch 75105

Featured Help Information

Miscellaneous Media

Continue Researching