Solution for Allowing Torklift Tie Down TLF3006 To Install All the Way

Question

Question:

2016 ford f250 superduty 6 3/4 bed I discovered that the adapter sleeves are not need and the receivers on both sides fit directly into the trailer hitch cross frame but will not fit completely into the trailer hitch. this causes the retainer clamps to be approximately half inch too short and I cannot secure receiver to the trailer hitch on either side. any ideas

asked by: Mike B

0

Expert Reply:

For the install of the Torklift # TLF3006 the directions suggest using a hammer and chisel to remove the excess welding flash inside the ends of the factory hitch to allow the tie down to fully seat. We've heard that a dremel actually makes the job a bit easier.

expert reply by: Jameson C

0

Answer 1

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 2

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hey Ryan! The BulletProof Hitches Aluminum Adjustable 2-Ball Mount #BPH47MR weighs 18 lbs. It has a 6061 T6 grade aluminum construction with a max rise/drop of 6". What kind of trailer are you towing?

view full answer...

Answer 7

Good afternoon Ron, congrats on the new truck! Those are sweet. For your application with the 8 foot bed, OEM hitch, no running boards etc., you'll want the TorkLift Tie Downs - Custom Frame Mount - Front and Rear #TL87DR. They also come in…

view full answer...

Answer 8

Hi Clint, welcome back The HappiJac Original Turnbuckles for Camper Tie-Downs - Stainless Steel - Qty 4 #LC182898 are likely what you are looking for and will be a good in between option (they are actually pretty nice and should last a good long…

view full answer...

Answer 9

Hey Jack, yes the Torklift camper tie downs part #TL63PR are the correct set for your 2024 Ford F-350 Tremor with a short bed and factory hitch. The turnbuckles part #TLS9526-2 that you referenced as well would be a great set that matches what you…

view full answer...

Answer 10

Hello Gary, Thanks for writing in! I'm glad you found us. I'm especially glad you asked about TorkLift tie-downs. If you're hauling a truck camper, they're my favorite option because they're built specifically for the truck and…

view full answer...

Answer 11

Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.

view full answer...

Solution for Allowing Torklift Tie Down TLF3006 To Install All the Way

Product Page this Question was Asked From

Continue Researching