How to Order 3,500 lb Dexter Axle 35545I-EZ-89 with 5 on 5-1/2 inch Bolt Pattern Idler Hub

Question

Question:

Do you carry this axle in a 5 on 5.5 inch bolt pattern?.

asked by: Curry M

0

Expert Reply:

What we do offer that will give you the axle you mentioned with the bolt pattern you want is for you to order the axle part # T3584F-8974 and then use the idler hubs part # AKIHUB-555-35-K that fit this axle and have the 5 on 5-1/2 inch bolt pattern you need.

expert reply by: Jameson C

0

Answer 1

The wiring of the Replacement Solenoid Valve #T4748800 is ran to the reverse light circuit of the trailer's wiring connector. Basically one wire will get run to the reverse light circuit and the other wire will get grounded on the trailer frame.…

view full answer...

Answer 2

Hey Jason, yes the etrailer axle part #e75SR is pretty close to what you need but it does have the spring seats incorrectly placed based on what you need. But if you don't mind moving them you could have them rewelded at the distance your trailer…

view full answer...

Answer 3

I wish there were an exact answer to your question but since there are so many variables involved in the wear of an axle it is impossible to determine the lifespan of an axle no matter if it is a torsion axle or a standard axle like part…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

How to Order 3,500 lb Dexter Axle 35545I-EZ-89 with 5 on 5-1/2 inch Bolt Pattern Idler Hub

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching