Video That Shows How to Remove Lock Core of Fastway Adjustable Ball Mount

Question

Question:

How can I remove the locking mechanism. By remove, I mean take it apart.

asked by: Ariel T

0

Expert Reply:

There is a re-keying kit we offer for the ball mount part # DTALBM6625 it is part # DTLBM02RK. It comes with new lock cores and a wrench that allows you to remove the lock cores.

I attached an install video for the kit that will walk you through the entire process. Basically on the very top under a sticker that removes and exposes an allen bolt. When that's loose the core slides out.

expert reply by: Jameson C

0

Answer 1

Without the key or the key number you will need to remove the locks that are on your Diversi-Tech ball mount and replace them with Diversi-Tech 2-Pack Re-Keying Kit, #DTLBM02RK. This kit will have 2 keyed-alike lock cylinders with 4 keys and lock…

view full answer...

Answer 2

According to my buddy at Diversi-Tech, the set screw that holds the lock cylinder in uses a .050 inch Allen wrench. Before attempting to remove the screw, I would highly recommend soaking the set screw with some penetrating oil because the set screw…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi Richard! From the top of the shank to the lowest part where the tri-ball sits on the #BWTS20067BMP is 11.125". If you have the balls at max drop with the tallest one hanging down that would be 12.5". We recommend at least 11" of…

view full answer...

Answer 12

Hi John! The BulletProof Aluminum Hitch w/ Stainless Steel Dual Ball for 2" Hitch - 4" Drop/Rise - 14K #BPH32YR is anodized, so it isn't just raw aluminum. That actually goes for all of BulletProof's aluminum ball mounts, which is…

view full answer...

Video That Shows How to Remove Lock Core of Fastway Adjustable Ball Mount

Featured Help Information

Miscellaneous Media

Continue Researching