Replacement Screen For Ventline Roof Vent On 2005 Springdale RV

Question

Question:

i am looking a ventling screen radius corner off white for my 05 springdale rv can you help me please

asked by: Tom L

0

Expert Reply:

We have a few of the replacement screens that are designed for Ventline roof vents.

The replacements depend on the vent you have on your RV. If you have a Ventadome 110V vent, then the screen you need is part # BVA0444-42. I have attached a link to our product page for the screens we offer. You will want to take note of the attach points on the replacement screen.

expert reply by: Jeffrey L

0

Answer 1

Based on the number you listed the cover you are looking for is #BVD0449-A01 for a white cover or #BVD0449-A03 for a tinted smoke cover. The replacement screen frames come in Polar White #BVC0573-41 or Birch White #BVC0573-31.

view full answer...

Answer 2

The opening on your snowmobile trailer is most likely 14-1/4" x 14-1/4" as that is the standard size that nearly all newer trailers on the market use. In order to find the correct one for you we would need to know what type of hinge you…

view full answer...

Answer 3

Hey Tim, To replace the cover of your Ventline V2094 RV roof vent you can use either part #BVD0449-A03 (smoke) or #BVD0449-A01 (white). I've attached a short video below where Shane will walk you through the installation process.

view full answer...

Answer 4

The lips on the Replacement Dome Seal #BVD0455-01 will face out and up, respectively. You can see it fairly well in the picture I have included.

view full answer...

Answer 5

I would start off by trying to secure the corners of the Replacement Dome Seal, #BVD0455-01, using a silicone sealant like the TremPro 644 Silicone Sealant, #0160297. I am unsure if trimming the corners will help.

view full answer...

Answer 6

For your vent covers, there are four different hinge types that you might have. In order to know which replacement cover you need, the hinge style is very important. The sizes are all compatible, but the hinges are not. I've attached a photo to…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Screen For Ventline Roof Vent On 2005 Springdale RV

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching