Securing Replacement Dome Seal # BVD0455-01

Question

Question:

Hi, having trouble getting the corners of the replacement seal to stay on. I see that someone said use a little silicone sealant in the corners, what product exactly would that be? And should I cut or trim the corners to try to help it stay on. Thank you

asked by: Susan W

0

Expert Reply:

I would start off by trying to secure the corners of the Replacement Dome Seal, # BVD0455-01, using a silicone sealant like the TremPro 644 Silicone Sealant, # 0160297.

I am unsure if trimming the corners will help.

expert reply by: Leah S

0

Answer 1

I believe this seal was 3/8" wide when initially installed an over time it has been stretched. As long as you have one of these models: the Ventline Ventadome roof vent models manufactured after 2008, V2092, V2110, V2094, V2119, and V2128, it…

view full answer...

Answer 2

For a gasket you could use with a roof vent that uses the lid part #BV0554-01 you'd want the part #BVD0455-01.

view full answer...

Answer 3

The SAE numbers are not always super reliable and is not always the best information to go off of when finding a new replacement lens. Instead, I recommend measuring your current lens and take note of its shape/color and let me know. From here,…

view full answer...

Answer 4

Normally the SAE number isn't a reliable way to find the correct replacement as it is not a part number, but from different customers in the past we've determined that the number you listed is for the Bargman Light Lens #34-59-010. This lens…

view full answer...

Answer 5

Sorry about your lenses being damaged. The good news is that replacement lenses are available for the Fender Clearance Light, part #BA44FNL. The amber lens is part #A44AB, the red lens is part #A44RB.

view full answer...

Answer 6

The lips on the Replacement Dome Seal #BVD0455-01 will face out and up, respectively. You can see it fairly well in the picture I have included.

view full answer...

Answer 7

You simply measure between the tires about an inch off the ground to determine what Fastway chocks are the best fit for your application. We have the Fastway ONEstep Wheel Chock for Tandem-Axle Trailers and RVs - 16" to 24" Long…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Securing Replacement Dome Seal # BVD0455-01

Products Featured in This Question

Continue Researching