Replacement Wheel Bolt and Stud For Keystone Sprinter 5th Wheel

Question

Question:

Wheel Bolt and Stud for 2015 Keystone Sprinter 5th wheel

asked by: Paul B

0

Expert Reply:

You will need to check the diameter and length of the wheel bolt you are looking to replace. We do have replacement options for your hubs whether they are 1/2 inch diameter like # K12WB169, 9/16 inch like # K916WB25, or 5/8 inch like # K58WB316. I have linked our page so you can see all your options of wheel studs. I have also linked the pages for wheel bolts in both coarse and fine thread.

We also have lug nuts for all these bolt/stud options.

expert reply by: Jason S

0

Answer 1

Hi Robert! The 17-1/2" wheels are a bit more limited than other offerings, but I think you may be interested in the following two options: Americana Hub-Piloted Solid Center Wheel w -0.5" Offset - 17-1/2" x 6-3/4" - 8 on 6-1/2 -…

view full answer...

Answer 2

A Dexter 8k hub would have an 8 on 6-1/2 inch bolt pattern like what the part #TA45ZR has. This is also a 17.5 inch diameter trailer wheel. For a mod style wheel instead, we have the part #TA35ZR.

view full answer...

Answer 3

The Taskmaster Modular Wheel w/ +0.08 Offset - 17-1/2" x 6-3/4" Rim is offered in both silver as part #TA35ZR and white as part #TA36MR. That said, they are designed for use with 5/8" wheel studs. The only 17-1/2" wheels we offer…

view full answer...

Answer 4

I have attached for you below a list of all our 17.5" x 6.75" trailer wheels with an 8 on 6-1/2" bolt pattern below. There are a few different types of wheels in this list such as aluminum/steel, dually/standard, and hub/lug centric.…

view full answer...

Answer 5

Hey Robert, To find your offset you'll need to measure from the mounting surface of your lugs to both outer edges of your current wheels. A negative offset will move the tire further away from the trailer while a positive offset brings the tire…

view full answer...

Answer 6

It might be possible to change out the studs in your hub from 9/16 to 5/8 if they are drive-in studs and not the type that threads in. If they are drive in and the diameter of the knurl end is approximately 0.6875 inches then you can replace them. We…

view full answer...

Answer 7

Hey Don. The Taskmaster Modular Wheel item #TA35ZR works with 5/8" lug studs. It does not have a center cap. The pilot hole diameter is 4.76". This is a 17-1/2" wheel with a 8 on 6-1/2 bolt pattern. It has a 5,956 lbs capacity per…

view full answer...

Answer 8

If you keep the trailer tires inflated to the maximum psi indicated on the tire sidewall then they should not bow out on the sides enough to cause any clearance problems between the tire and the trailer. A 1/2 inch space could be enough but it is…

view full answer...

Answer 9

There is no way we can tell you what lug locks would be used on your 2019 Geo Pro 15TB is. What you're going to need to do is measure the lug studs on the trailer when you pick up the trailer. The most common sizes are: 1/2"-20 short #12CLN,…

view full answer...

Answer 10

Hey Randy, thanks for reaching out! The Taskmaster Solid Center Wheel w/ -0.31 Offset #1750865SP1125 is a standard 17-1/2" wheel with an 8 on 6-1/2" bolt pattern and fits over 5/8" studs so it sounds like it will work for your…

view full answer...

Answer 11

You will want to stick with the same style of lug nut, so if you use 90 degree lug nuts, stick with that. The reason is the taper on the 60 degree lug nut is steeper, so there could be fit issues depending on your trailer wheel, as they are designed…

view full answer...

Answer 12

All of the trailer wheels we offer that are 17.5 inch in diameter are hub-piloted like the Taskmaster Solid Center Wheel #TA45ZR that you referenced. At the very least you'd have to go with new hubs that match this style of wheel as there…

view full answer...

Replacement Wheel Bolt and Stud For Keystone Sprinter 5th Wheel

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching