Is Lubricant Needed to Install Lippert Never Fail Axle Bushings

Question

Question:

lippert never fail bushing kit. what kind of lube, if any, can i use to help the bushings go in to the spring eyes ?

asked by: Robert B

1

Helpful Expert Reply:

There is no lubrication necessary for the Lippert Never Fail Bushings # LC281285. In fact they should not be lubricated since it can degrade the bushings. I've linked a video that shows the installation.

expert reply by: Charles S

1

Answer 1

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 2

Hey Michael, so the Curt Trailair part #LC155943 that you referenced was not designed to offer a different ride height from the pin boxes it replaces so it would not be the way to go if you were wanting to make a height adjustment. What I would do is…

view full answer...

Answer 3

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 4

Thanks for reaching out! To lift your 2020 Grand Design Reflection 150 260RD 5th Wheel so it's 2" taller I recommend using the Correct Track Trailer Alignment and Lift Kit #RR23QX. This installs using the same frame mounting brackets that…

view full answer...

Answer 5

Since your axle is mounted on top of the leaf spring you will want between 2 and 2-1/2 inches between the top of the axle and the trailer frame. You will also want 3 inches of clearance between the top of the tire and the fender. Check out the FAQ…

view full answer...

Answer 6

Generally speaking you will want to have 3 inches minimum from the top of your tire to the fender of your trailer to accommodate for suspension travel. Having a little more wouldn't hurt, but I wouldn't recommend any less than 3 inches.…

view full answer...

Answer 7

Between 4 and 6 inches is typically what is recommended as minimum clearance from trailer overhang to bed rails. If you can level your setup by lowering hitch where you'd have 5 inches you should be fine. Especially if you aren't in an area…

view full answer...

Answer 8

I attached a link to a page that has install instructions for the Correct Track kit part #RR23QX that you referenced. I'd recommend the shackle bolt kit part #MR58ZR as it comes with the correct size bushings, bolts, and shackle straps.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Is Lubricant Needed to Install Lippert Never Fail Axle Bushings

Featured Help Information

Miscellaneous Media

Continue Researching