Westin Stainless Steel Nerf Bars to Fit 1995 GMC Regular Cab Pickup

Question

Question:

Hello,Im looking for westin 3 inch round stainless nerf bars for my 1995 GMC reg cab. I have Westin now,which were damged in an accident. They need to be about 50 inches overall or close.

asked by: Jeff K

0

Expert Reply:

The 3 inch stainless steel Westin Ner Bars # 23-0500 are confirmed to fit your 1995 GMC truck. They run the length of the cab and have a 3 inch step pad on each bar.

expert reply by: Charles S

0

Answer 1

I believe the remaining wire you're speaking of is actually light blue, and is meant to provide power for a third brake light installed on a camper shell. If you want to run a 12-volt accessory power circuit, you can run it from the positive…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hey Rod, thanks for reaching out. Yes, it will! The Curt Helux Shock-Absorbing 5th Wheel Pin Box #C83RJ will indeed work with the Demco Autoslide 5th Wheel Hitch #DM8550038. Just make sure you also use the Demco Autoslide Locking Plate for Lippert…

view full answer...

Westin Stainless Steel Nerf Bars to Fit 1995 GMC Regular Cab Pickup

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching