Distance Between Loops on 8 Inch Roadmaster Safety Cables

Question

Question:

Looking at the 8 inch Safety Cable. What is the length between the two loops on the ends?

asked by: Keith H

0

Expert Reply:

The 8 Inch Roadmaster Safety Cable Extensions # RM-910648-8 measure approximately 3-1/2 inches between the loops.

expert reply by: Charles S

0

click to enlarge

Answer 1

Extending out the safety chains is definitely something that has to be done with the Swagman Original 4 Bike Towing Rack S64675. The RoadMaster 8" Safety Cable Extensions #RM-910648-8 will help get the job done but I do recommend picking up…

view full answer...

Answer 2

I reached out to my contact at EcoHitch to see if they have seen this issue before with the EcoHitch #306-X7201 on your Tesla and if they have any suggestions. My contact did say that the Tesla rear bumper has quite a bit of tolerance from the…

view full answer...

Answer 3

I have a solution for you, but I do not think getting a longer hitch pin is the answer. From the picture you provided, it looks like it is the S-hook of the safety cable that is getting behind your hitch pin and the pushing into the hitch lock side…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Adam, the correct Kuat DEK Platform rack with light bar for your 2026 Toyota Tacoma would be the part #KU73SR. The correct Kuat Ibex Overland Truck Cap then too would be the part #KU99SR that you referenced. Now the top of this would be lower…

view full answer...

Answer 12

Hey William, so the 3 inch hitches do use the larger hitch pin diameter but the 2-1/2 inch hitches still use the smaller one. So with a reducer like the part #38735 technically you would use both sizes. If you check out the picture I attached you can…

view full answer...

Distance Between Loops on 8 Inch Roadmaster Safety Cables

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching