Will Convert a Ball Ball Mount Fit Curt Trailer Hitch

Question

Question:

Will a converta-ball ball mount fit a curt hitch?

asked by: Matt

0

Expert Reply:

Yes a Convert a Ball Ball Mount like the part # AMSC12 that you referenced would fit a 2 inch Curt trailer hitch.

For more information on how to pick out the correct rise/drop ball mount to allow a trailer to be towed level check out the help article link I attached.

expert reply by: Jameson C

0

Answer 1

The Ball Mount Adapter for Convert-A-Ball Cushioned Weight Distribution Shank #BA-1 only fits on weight distribution shanks and would not fit the shank of the Curt #C45900. You'd want to use it with a shank like the part #AMAC1 instead.

view full answer...

Answer 2

Yes you can use the Ball Mount Adapter for Convert-A-Ball Cushioned Weight Distribution Shank #BA-1 with your Curt Adjustable 2-Ball Mount #C99NR as they have the same 1-1/4" hole spacing and use the same 3/4" adjustment pins.

view full answer...

Answer 3

The channel on the #C28KR is too narrow to fit on the Curt Adjustable 2-Ball Mount #C99NR (45935) shank. What you can use instead is the Ball Mount Adapter for Convert-A-Ball Cushioned Weight Distribution Shank #BA-1. This has a 1" diameter hole…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Thomas! The distance from the center of the hitch pin hole to the center of the ball on the #BW77BR is 13-5/8". This is designed to fit a 2-1/2" receiver with a 10k rating for the 2" and 21k rating for the 2-5/16" ball. What…

view full answer...

Answer 9

Hey Tyler, thanks for reaching out. I'm sorry to say no, we don't have a 5 on 4-1/2" hub, or any hub for that matter that fits a 3/4" straight spindle. That kind of spindle was really only seen on older trailers and is basically…

view full answer...

Answer 10

Hey Rob, I’d be wondering the same thing if I came across a ball mount made out of aluminum like the #BPH77MR while researching. Totally fair question. That said, I haven’t seen any noticeable difference in slop or wear compared to their steel…

view full answer...

Answer 11

Probably not unless you want to cut that round hole into a 2-1/4" square. The Square A-Frame Jack w/ Footplate item #e74VV is designed for a-frame trailer's that have a square cut out not the standard 2-1/4" circular cut out which I am…

view full answer...

Will Convert a Ball Ball Mount Fit Curt Trailer Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching