Fuse location in Honda Pilot 2016 for Tekonsha 3070-P Brake Control Wiring Adapter for Honda

Question

Question:

To enable Tekonsha Prodigy P3 Brake Controller in Honda Pilot 2016 using Tekonsha 3070-P Brake Control Wiring Adapter for Honda, which fuse need to be enabled and what is its location so that the 7 point setup I bought from you guys will work with braker controller. Thank you in advance for helping.

asked by: Pankaj B

0

Expert Reply:

Your Tekonsha Prodigy P3 # 90195, can be installed using the # 3070-P if you have a factory tow package. It attaches with a simple clip connection to a plug under the dash of your vehicle near the parking brake. It isn't always easy to find in the midst of the wiring. Check out the installation video I've attached for you. There is not an extra fuse needed in this installation.

expert reply by: Jason S

0

Answer 1

Sounds like your 2007 Honda Ridgeline has a factory 7-way installed in it. To install a brake controller in your vehicle all you will need is the correct install harness. If you went with a Tekonsha brake controller like the P2 part #90885 all you…

view full answer...

Answer 2

The Prodigy P2 #90885 is an excellent choice, being one of our most popular and easy to use brake controllers of all time. To install the brake controller, first look under the dash under the steering column over the brake pedal as shown in the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Fuse location in Honda Pilot 2016 for Tekonsha 3070-P Brake Control Wiring Adapter for Honda

Featured Help Information

Miscellaneous Media

Continue Researching