Replacement Mounting Hardware for Yakima SwingDaddy

Question

Question:

Is replacement part set # Y8780022 also compatible with the Swing Daddy 4 hitch? Thx

asked by: Mark H

0

Expert Reply:

The correct kit for the older SwingDaddy # Y02422 is actually the part # Y8890185.

expert reply by: Jameson C

0

Answer 1

It looks like you purchased the Replacement Mounting Hardware, #Y8890185. This should have come with the square, black shank insert, a square nut that fits inside of the shank insert, a flat washer, a lock washer and a threaded pin and clip. I made a…

view full answer...

Answer 2

Thanks so much for the photos, they were very helpful. To replace all four cradles, what you need is two of the Replacement SuperCush Anti-Sway Cradle and ZipStrips #8880598 (which has the upper and lower ZipStrip) along with two of the Replacement…

view full answer...

Answer 3

If you look at the provided diagram, you can see the replacement parts that Yakima offers for your Ridgeback Bike Rack. If what you're needing isn't shown, please let me know what you're needing. Zip strips #Y8890297 Endcap #8890306…

view full answer...

Answer 4

Both the RidgeBack #Y02459 and FullTilt #Y02463 are high-end hanging-style racks from Yakima but in this case the FullTilt has a few extra features so I recommend going that route. Both racks have very similar features as far as tilting/folding ease…

view full answer...

Answer 5

From the center of the hitch pin hole to the handle of the Yakima FullSwing #Y02465 is 6". Since the handle is making contact with the spare tire on your 2018 Jeep JL Wrangler Unlimited Sahara it sounds like a better option would be to use the…

view full answer...

Answer 6

My contact at Yakima confirmed that the replacement cradle part number for the older generation of their SwingDaddy Hitch Mounted Bike Carrier is part #Y8890179. If this does not match the appearance of your existing cradles please provide a photo…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Mounting Hardware for Yakima SwingDaddy

Continue Researching