Dimensions of Fulton F2 Jack F1413040134

Question

Question:

Im considering this jack for a military utility trailer. This trailer sits up high. I need to know the maximum distance that can be achieved.

asked by: Mike S

0

Expert Reply:

The Fulton F2 Swing-Up Trailer Jack # F1413040134 has a moveable mounting bracket that provides an adjustment range of 8-inches.

The height from bottom of mounting bracket to the floor is Extended: 21-1/2" and Retracted: 11-1/2".

Check out the review video for more helpful information and measurements.

expert reply by: Adam R

0

click to enlarge

Answer 1

With the ARK Xtreme Off-Road Swing-Up Jack #ORJW500D in its lowest position it is 6.49" from the center of the mounting point to the top of the jack. The other end of the jack when fully retracted is going to be 18.89" from the mounting…

view full answer...

Answer 2

We do have the Replacement Pull Pin Kit #F500136 which is the part number 18 in the photo you found. We do not carry the part number 4 for the Fulton F2 Trailer Jack #F1413040134 at this time so you may need to replace the parts from another damaged…

view full answer...

Answer 3

Thanks for the picture, it looks like you have the Fulton F2 Swing-Up, Wide-Track Trailer Jack #F1413040134 in which you'd need the Wide-Track Wheel Assembly for Fulton F2 Adjustable A-Frame Jack #F500266 for a replacement.

view full answer...

Answer 4

Thank you for the photos of your friend's Fulton F2 trailer jack that has a broken caster wheel assembly. I wish I had better news for you but my contact at Fulton advised that this jack cannot be serviced. The entire unit will need to be…

view full answer...

Answer 5

Thanks for the photo. The Fulton F2 jacks use a different mount so it isn't compatible with your current base. You will need to remove the base and then you can install the F2 #F1413040134 you referenced. This F2 will come with all new mounting…

view full answer...

Answer 6

Since the location of your hitch pin hole and the safety chain tabs don't allow you to use a skid wheel like part #UF48-979020 or #RM-050, the only other option that may work is if you welded a skid wheel like part #UF48-979021 onto the bottom of…

view full answer...

Answer 7

Yes, the Sleeve-Lock Trailer Coupler #CTA-196 will fit the channel bracket that comes with the Brophy Lunette Ring w/ 3-Position Adjustable Channel Bracket #BR43ZR. The bolt holes match as well when it comes to size and spacing so you'll be good…

view full answer...

Answer 8

The spring part #CA-5196-SPR that you referenced is the spring of the coupler like part #CTA-196 that pushes the parts of the coupler apart when the sleeve is pulled back. I attached a picture that shows a very similar Bulldog coupler. You can see…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Dimensions of Fulton F2 Jack F1413040134

Featured Help Information

Miscellaneous Media

Continue Researching