2-5/16 Inch Trailer Hitch Balls With 1-1/2 Inch Diameter Shank

Question

Question:

I need a 2 5/16 ball with a 1 1/2 inch diameter shaft, 3 1/2 inch long shaft. There can be a rise of 1 inch, but is not necessary. Could you please help me find this ball please?

asked by: Keith K

0

Expert Reply:

We have 2-5/16 inch hitch balls with a 1-1/2 inch diameter shank.

You asked about a 3-1/2 inch long shank. The hitch balls we offer all have 2-3/4 inch long shanks. The closest we have for the dimensions you asked about is part # BWHB94005 which has a 1-inch rise, but as I mentioned has a 2-3/4 inch long shank.

expert reply by: Jeffrey L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Mark, the only real downside to an offset ball like the Gen-Y part #GY43XR is going to be that it costs more typically and it would take up more room when stored compared to a non-offset ball like the #C38CR. The handling and weight carrying…

view full answer...

Answer 9

Hey Kim, thanks for reaching out. The Firestone Ride-Rite Air Bags with Easy Mount Compressor #F24XV do fit your 2020 Ram 2500 with rear coil springs, but the hang-up is the under-bed gooseneck hitch. On your truck, the air bag brackets and the…

view full answer...

Answer 10

With a 2022 F350 short bed, hitting the top of the bed rails should not be an issue with most campers. Turning clearance however, will certainly be a factor. That is one advantage of the Andersen Ultimate hitch #AM3200, as it provides a 9"…

view full answer...

Answer 11

No, I am sorry it does not. I just spoke with Lippert and none of the Curt Helux Shock-Absorbing 5th Wheel Pin Box like item #C73RJ are compatible with gooseneck adapters like the Anderson Ultimate 5th Wheel Hitch. You would need to use a standard…

view full answer...

Answer 12

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

2-5/16 Inch Trailer Hitch Balls With 1-1/2 Inch Diameter Shank

Product Page this Question was Asked From

Continue Researching