Dimensions of the Replacement Pin Kit BD0233060301

Question

Question:

what is length / width of this pin ? thanks.

asked by: Charles

0

Expert Reply:

I spoke to my contact at Bulldog and he informed me that the length of the pin is 7 inches overall and has a usable length of 5-1/2 inches depending on how the ring is setting.

Diameter is 3/4 inches.

expert reply by: Jameson C

0

Answer 1

The pin holes in the B&W Extend-A-Goose Gooseneck Coupler #BWTEXA4200 are 3/4" in diameter for a 3/4" Pin #BD0233060301. The 8 holes are spaced 1" on center vertically for 8" range adjustment.

view full answer...

Answer 2

We sure do! I'd recommend part #AKBRKR-MC which provides 10 magnet retaining clips that are compatible with Dexter 10 and 12 inch brake assemblies.

view full answer...

Answer 3

The magnet clips #BP19005 should not be making contact with the drum while the brakes engage, so I do not think that is the problem. What I think is going on is it's just not seating all the way. These can get a little squished or deformed…

view full answer...

Answer 4

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Dimensions of the Replacement Pin Kit BD0233060301

Continue Researching