Bearing Buddy Replacement Recommendation and How to Determine Replacement Bearings
Published 08/04/2016
Question:
I have a 1996[?] Gator boat trailer. I am looking to replace the current [rusting] Fulton Bearing Protectors with SS Bearing Buddies. While I am at it, I was planning on replacing the bearings and seals as well - its been at least 7 years since they were replaced. Question - The current bearing protector measures 1.980 inches when removed at the hub end. What other measurements do I need to ensure ordering the correct seals/bearings, etc.?
asked by: Blaise
Expert Reply:
I am confident we have the parts you will need, but knowing which Bearing Buddy you have on your hub does not guarantee that we know for sure what bearings your hub has. The Bearing Buddy you need is the part # BB1980A-SS.
I really wish there was a way to determine what bearings a trailer needed without actually pulling the wheel off and checking, but there isn't. The only two solution I have for you would be to remove the hubs and get the numbers that are stamped on the bearing or for you to remove the hubs and use a digital or dial caliper to measure where the bearings and seal ride (see pic).
With that info I can help you figure out what you need.
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.99 Inch
- 2000 lbs Axle
- 2500 lbs Axle
- 3500 lbs Axle
- Bearing Buddy
more information >
Continue Researching
- Search Results: 9/16 lug nut
- Search Results: strap winch
- Search Results: car tie down straps
- Search Results: ratchet straps
- Search Results: trimax
- Search Results: umax
- Search Results: trimax locks trailer tongue lock
- Shop: Taskmaster Trailer Wheel Lug Nut - Chrome Plated - 9/16"-18
- Shop: Dexter Semi-Metallic Disc Brake Pads - 6,000 lbs to 8,000 lbs
- Shop: Mud Flaps
- Shop: Dexter Hydraulic Drum Brake Assembly - Duo Servo - 12" - Right Hand - 7,000 lbs
- Shop: B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 18K
- Shop: Dexter Trailer Brake Drum for 10,000-lb Axles - 12-1/4" - 8 on 6-1/2 - Non-ABS
- Shop: Demco Trailer Coupler - Flat Plate Mount - eZ-Latch - Black - 2-5/16" Ball - 21,000 lbs
- Shop: Demco Trailer Coupler - Flat Plate Mount - 3/4" Bolt Hole - 2-5/16" Ball - 21,000 lbs
- Video: Review of etrailer Trailer Hubs and Drums - Galvanized Idler Hub - AKIHUB-545-2-G-EZ-2K
- Video: Cleaning and Replacing Hubs and Bearings
- Q&A: Looking For Marine Grade Hubs For A Straight Spindle
- Q&A: How to Pick Out Bearing Buddy for Trailer Hub
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Shop: Suspension Enhancement
- Video: B&W Companion OEM 5th Wheel Hitch Manufacturer Breakdown
on Trailer Bearings Races Seals Caps
