What is the Inner Diameter of Replacement Bearing for Bulldog Square Jacks, # BD001015

Question

Question:

What is the inside diameter of this bearing? Thanks

asked by: Gordon

0

Expert Reply:

I spoke with my contact at Bulldog regarding the Replacement Bearing for Bulldog Square Jacks, # BD001015. He stated that the inside diameter is 0.876 inches. This is 1 thousand of an inch larger than 7/8 inches. The outer diameter is 2 inches.

We carry several other replacement gears for Bulldog jacks including # BD500106, # BD5002581360, # BD500156, and # BD500212.

expert reply by: Michael H

0

Answer 1

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Answer 2

Hi Dan; that does look like the Fulton HD25000101. Lining up the ruler with the bevel it looks like it is 1-5/16" wide just like the gear that comes with the #F0933306S00. Take a look at the dimensions for the parts below and see if that all…

view full answer...

Answer 3

It sounds like you have a Fulton or Cequent branded 1,000 capacity jack and are in need of a repair kit. The part #F0933302S00 is a repair kit for Fulton jacks with a weight capacity of 800-1,200 lbs. Based on the picture you submitted this should be…

view full answer...

Answer 4

Atwood jacks are no longer being produced which means replacement parts like gears are no longer available. The #BD5002581360 you looked at does have similar dimensions for the large gear, but it is designed for Bulldog jacks not Atwood. I understand…

view full answer...

Answer 5

It looks like you have a variation of the Fulton Marine Jack #FXP100W0301. For that the replacement bevel gear kit is part #F0933302S00 and work with Fulton marine and recreational jacks up to 800 lb to 1,200lb capacities. As long as your jack falls…

view full answer...

Answer 6

We do offer replacement parts for Fulton jacks, including the square tube type. These parts are not always a universal fit, so you will need to order replacement parts that are rated correctly for your particular Fulton jack. If you can find a model…

view full answer...

Answer 7

Yes, the Replacement Gears #BD5002581360 will fit your Bulldog Jack 190784. This kit is specific to the 190 series jacks up to and including 5,000lb lift capacities.

view full answer...

Answer 8

Yes, the Replacement Gear Kit, part BD5002581360, is made to be used with Bulldog series 190 jacks.

view full answer...

Answer 9

You are needing the Replacement Sidewind Gear Kit #BD5002581360 which will include the hex pattern thrust washer for the handle side of your Fulton Marine Jack #HD50000101.

view full answer...

Answer 10

I spoke with my contact at Bulldog regarding the Replacement Bearing for Bulldog Square Jacks, #BD001015. He stated that the inside diameter is 0.876 inches. This is 1 thousand of an inch larger than 7/8 inches. The outer diameter is 2 inches. None…

view full answer...

Answer 11

I attached a picture that details how to disassemble the Bulldog 12,000 lb jacks.

view full answer...

Answer 12

The replacement parts we have for the Bulldog Square Jack #BD182500 are a Replacement Gear Kit #BD500212 and a Replacement Screw and Nut Kit #BD500217. These are the two most likely aspects of the jack to be causing your problem. I have attached the…

view full answer...

What is the Inner Diameter of Replacement Bearing for Bulldog Square Jacks, # BD001015

Continue Researching