Replacement Gear Set For Bulldog 190784 5,000LB Trailer Jack

Question

Question:

Pin sheered for inner gear and need a replacement. Will this kit work for my jack? I attached a picture of what’s left of the pin and the sticker on the jack. Thanks

asked by: Bob B

1

Helpful Expert Reply:

Yes, the Replacement Gears # BD5002581360 will fit your Bulldog Jack 190784. This kit is specific to the 190 series jacks up to and including 5,000lb lift capacities.

expert reply by: Bud M

1

Broken Pin For Bulldog 190784 Trailer Jack
(click to enlarge)

Sticker For Bulldog 190784 Trailer Jack
(click to enlarge)

Answer 1

I spoke with my contact at Bulldog regarding the Replacement Bearing for Bulldog Square Jacks, #BD001015. He stated that the inside diameter is 0.876 inches. This is 1 thousand of an inch larger than 7/8 inches. The outer diameter is 2 inches. We…

view full answer...

Answer 2

It sounds like you have a Fulton or Cequent branded 1,000 capacity jack and are in need of a repair kit. The part #F0933302S00 is a repair kit for Fulton jacks with a weight capacity of 800-1,200 lbs. Based on the picture you submitted this should be…

view full answer...

Answer 3

Atwood jacks are no longer being produced which means replacement parts like gears are no longer available. The #BD5002581360 you looked at does have similar dimensions for the large gear, but it is designed for Bulldog jacks not Atwood. I understand…

view full answer...

Answer 4

Hi Dan; that does look like the Fulton HD25000101. Lining up the ruler with the bevel it looks like it is 1-5/16" wide just like the gear that comes with the #F0933306S00. Take a look at the dimensions for the parts below and see if that all…

view full answer...

Answer 5

We do offer replacement parts for Fulton jacks, including the square tube type. These parts are not always a universal fit, so you will need to order replacement parts that are rated correctly for your particular Fulton jack. If you can find a model…

view full answer...

Answer 6

It looks like you have a variation of the Fulton Marine Jack #FXP100W0301. For that the replacement bevel gear kit is part #F0933302S00 and work with Fulton marine and recreational jacks up to 800 lb to 1,200lb capacities. As long as your jack falls…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Gear Set For Bulldog 190784 5,000LB Trailer Jack

Continue Researching