Can a 2 Inch Ball be Included in a Ball Mount Kit Instead of a 2-5/16 Inch Ball

Question

Question:

Can i order this kit with a 2inch Ball instead of 2 5/16?

asked by: Kevin

0

Expert Reply:

What you can do is get the parts individually since we can't swap the balls out in a kit. The ball mount is # RP45323 and the bag is # ETBMB. For a 2 inch ball that will fit use # A-90. But keep in mind that the ball is rated for 10,000 pounds which is less than the ball mount which is rated for 18,000 pounds gross trailer weight and 2,000 pounds tongue weight.

expert reply by: Michael H

0

Answer 1

The Ball Mount #RP45322 in the etrailer Ball Mount Kit for 2-1/2" Hitches #EBMK25318 is 10" from the center of the hitch pin hole to the center of the ball hole.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 11

Hi Fred! The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F24XV will indeed fit your 2025 Ram 2500 with the factory puck system. The only vehicles it won't fit are ones that have the factory…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Can a 2 Inch Ball be Included in a Ball Mount Kit Instead of a 2-5/16 Inch Ball

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching