Thread Size of the Lippert Components JT's Strong Arm Jack Stabilizer Replacement T-Bolts

Question

Question:

I need a t handle bolt and see Lippert Components Accessories and Parts - LC314594. I need a 3/8 course thread bolt. Is that what this is?

asked by: T B

0

Expert Reply:

Yes, I went out and checked a Lippert Components JT's Strong Arm Jack Stabilizer Replacement T-Bolts # LC314594 we had in stock and the threads are 3/8 inch coarse.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

The seal you need for your trailer hub is the #58846. Or for a bearing kit that includes all of the components you'll need you'd want the #BK2-100. For brake assemblies you'd want the part #AKEBRK-35L for the left side or part #AKEBRK-35R…

view full answer...

Answer 6

Yes. You can replace the Progressive Dynamics PD4590K18NS2 with the Replacement Converter Section for Progressive Dynamics 4500 Series RV Power Control Center - 90 Amp #PD4590CSV without any issues. Both are 90 amp converters from the same Series and…

view full answer...

Answer 7

Hey TJ! The new Furrion Chill Cube item #LC54DX is only compatible with other Furrion Cube components. You would need to purchase the Furrion Chill Cube item #FR69TD in white or item #FR49TD black if you would like to upgrade. A direct replacement…

view full answer...

Answer 8

Thanks for the photo, that was a huge help! You're needing 1/2 inch wire loom, which we sell by the foot as part #459075-1. I'd also use some 1/2 inch loom clamps, part #A0500 to secure the wire loom and hold it where it's supposed to…

view full answer...

Answer 9

Yes the Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote part #FV807350 does have a small led that stays lit indicating power.

view full answer...

Answer 10

I took a look at your Fastec 233468 CR6 Door Lock and it looks like the closest we have to the cutout you're needing is the Bauer Products Camper Door Lock #BA54FR which requires a cutout of 2 3/4" x 3 3/4" so it'd be about an inch…

view full answer...

Answer 11

Tan, it actually looks like the Replacement Hydraulic Pump Motor for Lippert RV Leveling Systems #LC57AF is the correct replacement for your Lippert 414850. To get this part though, you'd need to call into our customer service team and place your…

view full answer...

Thread Size of the Lippert Components JT's Strong Arm Jack Stabilizer Replacement T-Bolts

Product Page this Question was Asked From

Continue Researching