How Wide is Bulldog 8K A-Frame Coupler BD43805W0317 At the Back

Question

Question:

Looking at the coupler from the bottom . What is the measurement along the left edge of the plate the jack mount on. The coupler on my trailer is 10, is this the same.

asked by: Michael D

0

Expert Reply:

Someone else has recently asked that question and a coworker made a lovely picture showing the measurement you are looking for on coupler # BD43805W0317. I have included that picture for you here. The inner width is 10-1/4 inches and the outer is 10-3/4 inches.

expert reply by: Michael H

0

click to enlarge

August G.

5/14/2020

Hi I'm looking for an A frame trailer couple to make a class 3 tow bar. I'm needing one with out the holes for the trailer jack. Do you have one?

Chris R.

5/18/2020

All of our A-frame couplers feature a pre-cut hole for the trailer jack. We do have a nice selection of coupler-style tow bars available though, which I have linked below.

Helpful Links

dept-pg-tow_bar-sf-coupler_style.aspx

Answer 1

That is correct the inner dimension of the Demco A-Frame Trailer Coupler item #DM14793-95 is 10 3/4 inches. I have attached a picture that breaks down the measurements. You would need to fabricate a spacer on either side to attach this coupler to…

view full answer...

Answer 2

Your trailer should have an identification/safety sticker that indicates its gross vehicle weight rating (GVWR) which is the most the loaded trailer can weigh. If it is a brand new trailer this will unambiguously tell you its capacity; if it was…

view full answer...

Answer 3

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for attaching the…

view full answer...

Answer 4

Almost all A-frame jacks now have the triangle or round mounting plate with the 3 bolt-3 inch on center holes. We do not carry anything that has the 4 holes. We do have some electric jacks like the Stromberg Carlson Electric Trailer Jack - Drop Leg -…

view full answer...

Answer 5

Yes, you can absolutely drill holes in your trailer tongue to install the 10,000 lb capacity Buyers Products Straight Tongue Trailer Coupler #3370091560. This is a pretty common occurrence due to the various bolt hole patterns of straight tongue…

view full answer...

Answer 6

Hello Al, thanks for reaching out. The A-Frame Trailer Coupler #CA-5210-B and the Demco A-Frame Trailer Coupler #DM14793-81 are interchangeable. They both fit a 50" degree A-frame which is standard. I would be surprised to hear that your A-frame…

view full answer...

Answer 7

A standard 50 degree coupler like #DM14793-81 will work on your custom 45 degree frame with a little modification. Without welding shims the coupler will not have the strength, so you will need to make some adjustments to your current tongue design.…

view full answer...

Answer 8

From the rear of the coupler portion on the Demco A-Frame Coupler #DM14793-81 to the center of the center bolt hole there is a distance of 4-1/2 inches. From the rear of the A-Frame mount to the center of the center hole there is a distance of 4-3/4…

view full answer...

Answer 9

For the Demco A-Frame Trailer Coupler #DM14793-81 you can use the etrailer #e98887. This will fit the pin hole on the coupler keeping it secure. Another option is the #e98893 which fits over the coupler and blocks the ball opening. You could also use…

view full answer...

Answer 10

The Demco A-Frame Trailer Coupler #DM14793-81 (Black) or #DM14793-52 (Silver) do not come with bolts. You will need to use 1/2" Grade 5 hex bolts with them. I've added links to video reviews of each coupler for you to check out.

view full answer...

Answer 11

I went to our warehouse and measured the Demco A-Frame Trailer Coupler #DM14793-81 to get you the dimensions you need. From the UNDERSIDE of the top plate, the part of the coupler that will actually contact the top of the A-frame, the hole centers…

view full answer...

Answer 12

I made a trip out to our warehouse to get that measurement for you. The distance from the center of the hitch ball to the center of the jack mounting hole on the Bulldog Heavy-Duty Cast Head Coupler, #BD43805W0317, will be 14 inches. I have included…

view full answer...

How Wide is Bulldog 8K A-Frame Coupler BD43805W0317 At the Back

Continue Researching