Longer Ball Mount Recommendation With at Least 750 lb Tongue Weight Capacity
Updated 05/23/2016 | Published 05/17/2016 >
Question:
Ive got a 2008 Hummer H2 SUT. I have a rear mounted spare tire which sits directly over my hitch ball. I need to extend it out 6 to 8 inches but Im worried it not be strong enough to tow my 6500 LB Jayco Camper. Will one of your Blue Ox extensions be safe to use? Blue Ox is the only one Ive found rated above 5,000 lbs. Tongue weight on my camper is 750 lbs. Any advice is appreciated.
asked by: Bradley B
Expert Reply:
We most likely will have a solution for you, but hitch extenders end up cutting the capacity of a hitch by 50 percent. Your best solution would be to go with a longer ball mount to help give you that distance.
For example, the Brophy ball mount part # BH20 measures 13-1/4 inches from the center of the ball hole to the center of the hitch pin hole and it has a 10,000 lb capacity with a 1,000 lb tongue weight capacity.
I attached a page that has all of the longer ball mounts we offer with higher capacities for you to check out as well.
Product Page this Question was Asked From
Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Long Shank
- Brophy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Function Of Trailer Vents On Enclosed Trailer
- Video: What to Know About the Brophy Ball Mount for 2" Hitch
- Search Results: trailer hitch
- Search Results: ballmount
- Shop: Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 12-1/4" Long - 7,500 lbs
- Shop: Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
- Shop: Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 12" Long - 5,000 lbs
- Shop: Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
- Shop: Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
- Shop: Curt Dual Length Ball Mount for 2" Hitches - 1" Rise, 2-3/8" Drop - 7,500 lbs
- Shop: Curt Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 9-3/8" Long - 10,000 lbs
- Q&A: Solution for Hitch Extension With 1,000 Pound TW and 10,000 Pound GTW Capacity on 2000 F-350
- Q&A: Hitch Extender for 10,000 lb Travel Trailer Compatibility
- Article: How to Measure for Trailer Hitch Drop
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Q&A: Lock For B&W Tow & Stow 3-Ball Mount # BWTS10048B
- Q&A: Can I Take the Inners from Your etrailer 7K Jack and Put them in My Bulldog 5k Jack Welded to Frame?
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: How Often Should Bearings Be Greased And How Much Grease Should I Add?
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Which Hitches are Made in the USA
- Article: My Trailer Hitch Doesn't Fit


